by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
MichielCornelissen
Important notice: a lot of people have been very happy with this product, but, as can be read in some of the comments below, it's clear that this design is right on the edge of what Shapeways can produce to the right quality at this moment. If you buy it, there's a risk of having a less then perfect fit, colors can be different from what you see on the screen, and, depending on how you use your phone as well as the tolerances of the case, it has been reported that the polyamide material can give a sort of polishing/scratching effect on the metal rim of the phone (you can find descriptions online of how to remove these kind of blemishes, but it may still be annoying).
Shapeways has, in my experience, been very good with customer service on this item, so they'll be happy to either return your money or provide a new product if you would be one of the unlucky ones; but it's up to you if you want to run the risk that you may have to go through this process.
Essential protection for iPhone 4S and iPhone 4
Even though 4-4 may be the worlds lightest and smallest iPhone 4 case, it still provides great protection to the vulnerable edges of the iPhones' front and back covers - while all controls and connections remain accessible. Its slightly protruding profile helps prevent protect the glass when laying your phone down; using 4-4 can also help to avoid signal loss problems.
This bumper-style case may be combined with commercially available screen protectors. 4-4 is manufactured from tough and durable 3d printed polyamide; it has a slightly textured surface that gives you great grip on your phone. Available in white, black and limited edition colors - note that in white, the 3d printed material may get dirty more quickly - but you can (seriously!) dishwash this product, so that shouldn't be too much of a problem. The 4-4 case is designed to have a tight fit around for iPhone. To put the iPhone in the case, or take it out, start at one of the bottom corners, where there are no buttons. Colors in the images above are for reference only; please check under 'select material' to get the most up-to-date preview of currently available product colors. Product is shipped in basic Shapeways packaging.
4-4 fits the GSM and CDMA/Verizon versions of iPhone 4, as well as the new iPhone 4S.
A two pack of 4-4's in the same color is available at reduced prices here.
You can have a look at all the products in my shop here. Consider buying 4-4 together with The Wrap, a handy cable winder for the European iPhone charger.
If you have any questions or feedback on this product, please feel free to contact me directly via michiel(at)michielcornelissen(dot)com.
Shapeways has, in my experience, been very good with customer service on this item, so they'll be happy to either return your money or provide a new product if you would be one of the unlucky ones; but it's up to you if you want to run the risk that you may have to go through this process.
Essential protection for iPhone 4S and iPhone 4
Even though 4-4 may be the worlds lightest and smallest iPhone 4 case, it still provides great protection to the vulnerable edges of the iPhones' front and back covers - while all controls and connections remain accessible. Its slightly protruding profile helps prevent protect the glass when laying your phone down; using 4-4 can also help to avoid signal loss problems.
This bumper-style case may be combined with commercially available screen protectors. 4-4 is manufactured from tough and durable 3d printed polyamide; it has a slightly textured surface that gives you great grip on your phone. Available in white, black and limited edition colors - note that in white, the 3d printed material may get dirty more quickly - but you can (seriously!) dishwash this product, so that shouldn't be too much of a problem. The 4-4 case is designed to have a tight fit around for iPhone. To put the iPhone in the case, or take it out, start at one of the bottom corners, where there are no buttons. Colors in the images above are for reference only; please check under 'select material' to get the most up-to-date preview of currently available product colors. Product is shipped in basic Shapeways packaging.
4-4 fits the GSM and CDMA/Verizon versions of iPhone 4, as well as the new iPhone 4S.
A two pack of 4-4's in the same color is available at reduced prices here.
You can have a look at all the products in my shop here. Consider buying 4-4 together with The Wrap, a handy cable winder for the European iPhone charger.
If you have any questions or feedback on this product, please feel free to contact me directly via michiel(at)michielcornelissen(dot)com.
by
MichielCornelissen
The product at this page is the PadFoot model that fits perfectly to iPad 2 as well as the 3d and 4th generation iPad. For PadFoot for iPad 1, go here.
PadFoot, the popular viewing stand for iPad, is now available for iPad 2 and the 3d and 4th generation iPad.
PadFoot clips to the corner of your iPad and will securely stand it upright in both landscape and portrait mode. It’s great for watching movies, clips and slideshows, for making FaceTime calls, as well as for use in presentations and (shop) displays.
At just 10 grams, PadFoot is now even lighter and smaller than its predecessor, with an increased viewing angle for even more viewing comfort - while it’s as stable and sturdy as ever.
Price information
The prices of PadFoot have been reduced by up to 20%. If you like, you can save shipping costs by combining this product with another product, like the ones from my shop; or just browse the galleries. A wholesale pack of 4 PadFoots, at up to 30% lower prices, is available here.
General information
PadFoot is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Check the materials section of this website for more information. Colors are seasonal; current availability is shown at the bottom of this page - this may be different from the colors shown in the images above. Each product ordered is individually manufactured, just for you. If you are new to the Shapeways site: to order, you'll be asked to create an account (it's easy; you can even log in with Facebook or Twitter).
It's best to use PadFoot on a stable and horizontal surface. Always make sure that your iPad is placed all the way into the opening in PadFoot; resting the iPad on one of its two edges without buttons. PadFoot will only work if your iPad has no cover on it. Product ships in basic Shapeways packaging. For more information, visit www.michielcornelissen.com; if you have any feedback or questions on this item, please feel free to contact me directly at michiel (at) michielcornelissen.com.
Some of the reactions on PadFoot, when it was introduced:
“PadFoot - Finally an iPad stand I can settle on. The iPad stands up perfectly, and there is absolutely no wobble or shake... PadFoot is also absolutely great to watch movies on the iPad...”
smokingapples.com
“... I was surprised by how small and lightweight it was... the PadFoot is extremely portable... PadFoot will hold the iPad securely at an angle perfect for viewing slide shows or videos.”
the-gadgeteer.com
“This Little iPad Stand Can Still Do a Lot of Standing... The PadFoot does the job and stays out of the way.”
gizmodo.com
PadFoot: one of fastcodesign’s most wanted products...
fastcodesign.com
“... I think the PadFoot... is just the perfect partner for the iPad”
gizmodiva.com
“ Simple yet adorable: The PadFoot iPad stand. At first, I thought the iPad’s inherent lack of stand was a flaw... Now I’m kind of happy that the tablet didn’t come with one. Otherwise, we wouldn’t have cute little items like this...”
todaysiphone.com
“... the Padfoot, a minuscule, efficient iPad stand that is beautiful in its simplicity.”
freshbump.com
“We’ve seen quite a few iPad stands since it hit the market, but the Padfoot by Dutch designer Michiel Cornelissen is just a bit better than what I’ve seen so far... Perfect!”
minimalissimo.com
“Padfoot ist einfach und genial.”
stilsucht.de
Padfoot on NOTCOT
notcot.org
“Received my PadFoot. Works great!”
Robert, New York
...bought a PadFoot... Best iPad accessory ever! You won’t be sorry, it is so light... I love it.
‘xultar’
“Just got my beautifully minimal PadFoot iPad stand from Michiel Cornelissen. Nice!”
‘mr_phillip’, Scotland
“I’ve bought many accessories for iPad, but PadFoot is by far the most useful one I’ve come across. Simple, qualitative and ingenious.”
Mario, The Netherlands
PadFoot, the popular viewing stand for iPad, is now available for iPad 2 and the 3d and 4th generation iPad.
PadFoot clips to the corner of your iPad and will securely stand it upright in both landscape and portrait mode. It’s great for watching movies, clips and slideshows, for making FaceTime calls, as well as for use in presentations and (shop) displays.
At just 10 grams, PadFoot is now even lighter and smaller than its predecessor, with an increased viewing angle for even more viewing comfort - while it’s as stable and sturdy as ever.
Price information
The prices of PadFoot have been reduced by up to 20%. If you like, you can save shipping costs by combining this product with another product, like the ones from my shop; or just browse the galleries. A wholesale pack of 4 PadFoots, at up to 30% lower prices, is available here.
General information
PadFoot is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Check the materials section of this website for more information. Colors are seasonal; current availability is shown at the bottom of this page - this may be different from the colors shown in the images above. Each product ordered is individually manufactured, just for you. If you are new to the Shapeways site: to order, you'll be asked to create an account (it's easy; you can even log in with Facebook or Twitter).
It's best to use PadFoot on a stable and horizontal surface. Always make sure that your iPad is placed all the way into the opening in PadFoot; resting the iPad on one of its two edges without buttons. PadFoot will only work if your iPad has no cover on it. Product ships in basic Shapeways packaging. For more information, visit www.michielcornelissen.com; if you have any feedback or questions on this item, please feel free to contact me directly at michiel (at) michielcornelissen.com.
Some of the reactions on PadFoot, when it was introduced:
“PadFoot - Finally an iPad stand I can settle on. The iPad stands up perfectly, and there is absolutely no wobble or shake... PadFoot is also absolutely great to watch movies on the iPad...”
smokingapples.com
“... I was surprised by how small and lightweight it was... the PadFoot is extremely portable... PadFoot will hold the iPad securely at an angle perfect for viewing slide shows or videos.”
the-gadgeteer.com
“This Little iPad Stand Can Still Do a Lot of Standing... The PadFoot does the job and stays out of the way.”
gizmodo.com
PadFoot: one of fastcodesign’s most wanted products...
fastcodesign.com
“... I think the PadFoot... is just the perfect partner for the iPad”
gizmodiva.com
“ Simple yet adorable: The PadFoot iPad stand. At first, I thought the iPad’s inherent lack of stand was a flaw... Now I’m kind of happy that the tablet didn’t come with one. Otherwise, we wouldn’t have cute little items like this...”
todaysiphone.com
“... the Padfoot, a minuscule, efficient iPad stand that is beautiful in its simplicity.”
freshbump.com
“We’ve seen quite a few iPad stands since it hit the market, but the Padfoot by Dutch designer Michiel Cornelissen is just a bit better than what I’ve seen so far... Perfect!”
minimalissimo.com
“Padfoot ist einfach und genial.”
stilsucht.de
Padfoot on NOTCOT
notcot.org
“Received my PadFoot. Works great!”
Robert, New York
...bought a PadFoot... Best iPad accessory ever! You won’t be sorry, it is so light... I love it.
‘xultar’
“Just got my beautifully minimal PadFoot iPad stand from Michiel Cornelissen. Nice!”
‘mr_phillip’, Scotland
“I’ve bought many accessories for iPad, but PadFoot is by far the most useful one I’ve come across. Simple, qualitative and ingenious.”
Mario, The Netherlands
by
roessnakhan
A replica of Cobb's totem from the film "Inception". As a below review has noted, and from my own version, the top works very well, and spins upwards of 90 seconds before toppling. You just might be in a dream.
by
joabaldwin
This is a mobius strip of Level 1 or Super Mario Bros. The whole level is wrapped around itself in a single surface, and poor Mario begins and ends at the same spot every time :(
All the elements from the level are there: every mushroom, turtle, cloud and star. They are all carved out of the surface at different heights, which looks fantastic when you have a light coming from the side, and each block casts a shadow.
It's a great piece to have on your desk, or to hang from a string to let it spin around.
All the elements from the level are there: every mushroom, turtle, cloud and star. They are all carved out of the surface at different heights, which looks fantastic when you have a light coming from the side, and each block casts a shadow.
It's a great piece to have on your desk, or to hang from a string to let it spin around.
by
curvecreative
Nanolet
Everyone's wearing their Nano on their wrist nowadays, now you can wear it on a one part 3D printed nano bracelet.
The NANOLET simply wraps around your wrist and fits snugly up to your hand which is perfect for running and everyday use. An alternative to the plethora of nano watches that are around now.
Featured on: Mashable , Cult of Mac , Yanko Design and many more.
Suitable for medium sized wrists. Available in a range of colors
Medium is for a wrist of circumference 165mm - 185mm. The best way to measure your wrist is to wrap a piece of string around your wrist, mark it and then measure it. Maximum wrist size is 190mm.
Unboxing Video here
Click here for OTHER SIZES
Click here to visit our site
Or click here to keep up to date on Facebook
Interested in buying Nanolets in BULK at reduced price? For LARGE , MEDIUM and SMALL
by
isohedral
An espresso cup specially designed with fins, to ensure the successful deployment of your rocket fuel. All systems are go! Paraboloid bowl holds approximately 1.5 fl oz. or 45 mL. (Note that I previously claimed the cup held 60 mL. While my 3D modelling software still reports that as the internal volume, some combination of the printing process and glazing is robbing me of internal volume. Contact me if you'd be interested in a larger, more expensive 60 mL cup.)
After receiving feedback from Shapeways, I've created a slightly revised model for the cup. I'm told that this model will be easier to print and glaze, leading to a more reliable product. The changes are minor -- it's a little wider, a little heavier, and has more rounding on edges that were previously sharp (a 3D rendering shows the differences above).
Update (April 13th, 2013): The cup has had a great run on Shapeways, and I deeply appreciate the attention and positive feedback it has received. The bad news is that I've got to stop offering it for sale here. The good news is that the cup is now available commercially! It's being manufactured by Fred and Friends, sold under the name "Blast Off! Espresso Cup Set". It's already available for purchase online (perpetualkid.com, thinkgeek.com), and I'm sure you'll be able to find it in your favourite housewares store soon.
by
TerraCotta
If M.C. Escher had owned fidget toys, he would have worn "One ring to rule the ball" as a pendant. A single, continuous line contains a small ball that makes orbit after mesmerizing orbit but cannot escape, always held down in four directions. Available in solid, durable stainless steel with optional antique bronze and gold plated finishes to fit any context, "One ring to rule the ball" now also includes a free rubber necklace so that you can confuse your mind any time the fancy strikes you! One customer echoes many others in saying, "I couldn't put it down. This thing is just too fun!"
Purchases by those gracious customers have now paid for the design time on this piece so it is available on a pay-what-you-want basis. Ordering from this page contributes 5$ towards continuing work such as the new, even more impossible "One ring to pwn the ball" (just released October 18th!) which can be found at http://www.shapeways.com/model/145172/one_ring_to_pwn_the_ball.html and the open-source "Ultimate Desk Toy" at http://www.shapeways.com/model/109166/ultimate_desk_toy.html . To download the original 3d file for your own use under a CC-BY license ( http://creativecommons.org/licenses/by/2.5/ca ) click "Download" at top right . To learn more about this design or other work from Terra Cotta, visit our website at http://www.terracottapf.com
Purchases by those gracious customers have now paid for the design time on this piece so it is available on a pay-what-you-want basis. Ordering from this page contributes 5$ towards continuing work such as the new, even more impossible "One ring to pwn the ball" (just released October 18th!) which can be found at http://www.shapeways.com/model/145172/one_ring_to_pwn_the_ball.html and the open-source "Ultimate Desk Toy" at http://www.shapeways.com/model/109166/ultimate_desk_toy.html . To download the original 3d file for your own use under a CC-BY license ( http://creativecommons.org/licenses/by/2.5/ca ) click "Download" at top right . To learn more about this design or other work from Terra Cotta, visit our website at http://www.terracottapf.com
by
MarcoA
My case for Raspberry Pi computer. To be assembled with the "LED lightguide" model nr. 486757 (http://shpws.me/6yFP).
This is the case everyone is talking about! ;)
Features: snap-fit fixing system for the board, easy to mount/unmount; snap-fit closing system, no screw required; bottom holes for blocking the computer by screws (sliding mount); led lightguides (not included in this model, available here: http://shpws.me/6yFP ); pre-shaped hole for GPIO access, just cut it out to open.
In this page you can find a gallery of shots working cases by enthusiast users!
http://marcoalici.wordpress.com/raspberry-pi-case-gallery/
by
Bathsheba
A theorem walks into a bar...
The Klein Bottle is a mathematical joke: a surface with only one side. This one feels just right in your hand and opens bottles with ease and style. Built to last in steel, it's the perfect touch for any math fan's kitchen.
The Klein Bottle is a mathematical joke: a surface with only one side. This one feels just right in your hand and opens bottles with ease and style. Built to last in steel, it's the perfect touch for any math fan's kitchen.
Yes, it really works!
Klein not-a-bottle-opener is here.
by
VENERIDESIGN
Nuke Lamp it's is a unique table lamp, its complex surfaces were created using real fluid dynamics simulations.
IMPORTANT:
The lamp consists of 2 parts, then you will receive 2 packages.... (open more info)...
one containing the 3D printed piece from Shapeways, and a Kit containing the bulb and stand from Veneridesign, then please contact me info@veneridesign.com for shipping address.
Thank you.
IMPORTANT:
The lamp consists of 2 parts, then you will receive 2 packages.... (open more info)...
one containing the 3D printed piece from Shapeways, and a Kit containing the bulb and stand from Veneridesign, then please contact me info@veneridesign.com for shipping address.
Thank you.
by
MichielCornelissen
The Wrap is an accessory that attaches to the USB end of your iPhone charger, transforming it into a handy little cable winder for the charging cord.
This version of The Wrap works with recent US iPhone chargers and USB cables as shown in the images, up to those of iPhone 4 and iPhone 4S - please check before you purchase. There is currently no version of The Wrap available for iPhone 5 cables. It may work with other countries’ iPhone chargers too, but only if the geometry is exactly the same as the US version as shown here.
This product was originally developed for the European version of the iPhone charger - that version can be found here. The Wrap is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Colors may vary - please check in the 'select material' section above for the latest versions. Some powder residue from the printing process may be left on the product; if that's the case, it should be easy to clean off. Product is shipped in standard Shapeways packaging.
You can have a look at all the products in my shop here. Shipping rates are flat, so you could divide them over several products. If you have any feedback or questions on this product, please feel free to e-mail me directly at michiel(at)michielcornelissen(dot)com. If you like, follow me on twitter.
A wholesale offer of 8 units of The Wrap at reduced prices is now available here.
This version of The Wrap works with recent US iPhone chargers and USB cables as shown in the images, up to those of iPhone 4 and iPhone 4S - please check before you purchase. There is currently no version of The Wrap available for iPhone 5 cables. It may work with other countries’ iPhone chargers too, but only if the geometry is exactly the same as the US version as shown here.
This product was originally developed for the European version of the iPhone charger - that version can be found here. The Wrap is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Colors may vary - please check in the 'select material' section above for the latest versions. Some powder residue from the printing process may be left on the product; if that's the case, it should be easy to clean off. Product is shipped in standard Shapeways packaging.
You can have a look at all the products in my shop here. Shipping rates are flat, so you could divide them over several products. If you have any feedback or questions on this product, please feel free to e-mail me directly at michiel(at)michielcornelissen(dot)com. If you like, follow me on twitter.
A wholesale offer of 8 units of The Wrap at reduced prices is now available here.
