by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
Dotsan
No1 in the series of animal heads, a smaller version of the 570mm high Stag Head (which is not available on Shapeways)
There is also a 75mm version here and a 300mm version here
The Animal Head Collection.
No 2 is a Zebra.
No 3 is a Rhino. A large Rhino is also available.
No 4 is a Tiger.
Tiger Head 2.
Large Tiger Head.
No 5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination.
There is also a 75mm version here and a 300mm version here
The Animal Head Collection.
No 2 is a Zebra.
No 3 is a Rhino. A large Rhino is also available.
No 4 is a Tiger.
Tiger Head 2.
Large Tiger Head.
No 5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination.
by
Dotsan
This is a truly inspiring piece, designed to use the minimum material while keeping the cost low. This is large at 300mm high, it's a show stopper a head turner. Shapeways have been pushed to their limits to produce and ship this. It is strong but light and only needs small pin or nail to hang it. The fine 1.5mm wire structure comes together to create a wonderful majestic stag head and a wonderful balance of weight in the form while almost being invisible.
The Animal Head Collection
No 1 is a Stag Head.
No 2 is a Zebra.
No 3 is a Rhino.
No 4 is a Tiger.
Tiger Head 2.
Large Tiger Head.
5 is an Elephant.
We have created an alternative 580mm high flat version
There is also a 75mm version here
The Animal Head Collection
No 1 is a Stag Head.
No 2 is a Zebra.
No 3 is a Rhino.
No 4 is a Tiger.
Tiger Head 2.
Large Tiger Head.
5 is an Elephant.
We have created an alternative 580mm high flat version
There is also a 75mm version here
