Fahrgestell angepasst für Roco H0e-Lorenradsätze. Andere Radsätze passen möglicherweise nicht. Ich empfehle Frosted Ultra Detail als Material

Schienenschleifwagen der Leipziger Verkehrsbetriebe. Entstanden im Eigenbau.

HOn30/OO9 Freelance Diesel Locomotive Design #1

Features:
- Self Positionable Cab Doors
- 2 Driver's Cabs
- Full  Pilot Steps

Dimensions (Assembled)
Height (Above Railhead) 4cm (11.25 HO scale feet)
Width 2.5cm (7 scale feet)
Length (Without Couplers) 12.3 cm (35 scale feet)

Designed to fit on an N Scale GP40 chassis, but can be adapted to other chassis or gauges at your own risk. The floor of the body is solid to allow custom fitting for your needs.

This is a chassis you can configure yourself! Add you own motor, wheels and axles.

Configurations:
- Axles: 2, 3 or 4
- Wheelbase: completely free to choose
- Gearing:
1:47 = 8mm motor, 5mm pulley, 6.5mm belt
1:50 = 6mm motor, 5mm pulley, 6.5mm belt
1:64 = 8mm motor, 7mm pulley, 7.5mm belt
1:68 = 6mm motor, 7mm pulley, 7.5mm belt
1:81 = 8mm motor, 9mm pulley, 10mm belt
1:87 = 6mm motor, 9mm pulley, 10mm belt

The chassis is designed to be used with parts form Nigel Lawton. You need:
- A motor. choose from the 6*10mm, 6*12mm or 8*16mm motor. All with pulley
- A pulley, see gearing
- A belt, see gearing
- Tenshodo motor bogie gears. 2 axles: 1 set. 3 or 4 axles: 2 sets
- Wheels
- 1.5mm to 2mm shaft adapter. One for every axle
- 1.5mm Shafts. You need 3!
- Electrical pickup kit
- Optional but highly recommended: 4*2*1.5mm ball bearings (not available at Nigel Lawton)

The parts are connected by 2 1.5mm shafts. The motor bracket is to be super-glued to the chassis, as is the motor to the bracket. The gears and pulleys should fixated to shafts and wheels with treadlock.

Fits Kato 103 chassis

Henschel Fabia Narrow gauge locomotive.

Based on Fleischmann 7000 locomotive

Required for assembly:
Fleischmann 7000 locomotive
0,25 mm phosporus bronze wire(for pickups)
Mashima 10x15 MHK electric motor.

Tve4 pienveturin kori.
Finnish state raiways Tve4 shunter.

This is a H0 scale (1:87) model of a special German tram to repair the overhead contact line. The original is in action at the “Thüringer Waldbahn”. You need a motor bogie, a pantograph, wire for the rails, some paint, plastic windows and after a few hours here you are a finished tram model. H0 Straßenbahn Modell eines Arbeitstriebwagens der Thüringer Waldbahn. Sie benötigen einen geeigneten Antrieb, weiterhin einen Dachstromabnehmer, Draht für die Handläufe, etwas Farbe, Kunststofffenster und schon nach einigen Stunden ist Ihr Straßenbahnmodell fertig.

Will take Fox Valley (3601-.540" Axle ) 36" N gauge wheelsets

Spur H0 Modell eines Klima Schneepflug Bauart „Linz“
Dieser Schneepflug Typ wurde von Henschel in Kassel gebaut unter Verwendung von Rahmen und Fahrwerk der Firma Dolberg aus Rostock. Diese Schneepflüge waren bei beiden deutschen Bahnverwaltungen ( DR und DB ) im Einsatz.

H0 scale model snow plow type „Linz“
The snow plow type was built by Henschel in Kassel using framework and undercarriage produced by Dolberg / Rostock. These snow plows were used by two German rail way companies (DR and DB).

A flatcar without stakes.The stake pockets can be drilled out to improve appearance and function. There are supports for a handbrake wheel and shaft (not supplied) at one end that need to be drilled out. Based on the rolling stock of the Ohio River & Western Railway. This model is designed for N gauge couplers (microtrains 1015).These can be screwed to the mounting block at each end. Instructions

HSB Schneeschleuder LSF 071 (1:87) Schmalspur Schneeschleuder LSF 071 der Harzer Schmalspurbahn in Spur H0m HSB Snow blower LSF 071 Narrow gauge snow blower LSF 071 in scaleH0m

Two pair of HO scale wood beam freight trucks used under equipment of the US Military Railroads during the American Civil War. One of many similar types made by various builders, starting with the Pennsylvania in the late 1850s, this design was the last hurrah for the widespread use of wood sideframes in freight service.

54" wheelbase, canister coil springs, decorative spring plank columns. Flat faced journal boxes are of a type most often seen in Civil War photos by Russell, Brady etc.

This version mounts with a #2 screw (like those used by Athearn/Roundhouse MDC and others) with a recess for the screw head, and can accomodate a larger screw with a little reaming. They should look great under Alkem or BTS USMRR car kits and backdated MDC, IHC, and Mantua cars.

Requires 33" wheelsets with 1.010 inch axles (MDC, Kadee, Reboxx). Others may also fit.

Because of their small size and fine detail, Frosted Ultra Detail is the preferred material.

Clean with warm soapy water or alcohol and toothbrush before painting. It particularly greasy use a toothbrush soaked in Bestine rubber cement remover. Acrylics recommended.

Part Number HOT30s
contact panamintmodels@aol.com for painted models or other quantities.

1 x Alte Leichte Feldbahnwagen
1 x Alte Leichte Feldbahnwagen mit bremse
1 x Leichte Feldbahnwagen mit bremse
These wagons have been used to supply the troops during the 1th wold war.
After the war they ended up at several Narrow Gauge lines and served many more years of service

Roco or Eggerbahn Compatible!
Scale: H0e

Parts required to complete model:
3 set of Wheels:  Fleischmann 20024 or Roco 20024, available at your local model train store
You need a piece of 0,5mm brass wire and the Jig for H0e couplings
Material: Frosted ultra detail is Highly recommended. White strong and flexible is also possible, but lakes the detail.

This is a model of an NSB Bm87 Railcar. Included is the body, interior/baseplate and details. I have used a Bullant chassis from Hollywood Foundry to power mine, it was fitted with only minor alterations to the interior/baseplate.

Das Vorbild dieses Güterwagens wurde bei der Zillertalbahn 1960 aus einem ehemaligen O-Wagen der Lammingtaler Schleppbahn umgebaut. 1970 erhielt er die Drehgestelle des ehemaligen KOK-Beiwagens. Er war der klassische Gepäckwagen zu den Payerbacher Personenwagen. Lange Zeit war er als Fahrradwagen in Kaltenbach-Stumm abgestellt, seit kurzem wird er wieder in den Dampfzügen eingesetzt.

Das Modell gibt den Zustand ab 1970 wieder. Der Teilesatz beinhaltet den Wagenkasten, Rahmen, Drehgestelle mit Pins und Bremsschläuche.

Es werden Kupplungen mit Aufnahme nach NEM355 benötigt, sowie N-Radsätze mit 6,2mm Durchmesser von Piko oder Fleischmann.

This slag car is from the 1920's. It is smaller than those you find in steel mills. The final model will require details by the purchaser. Add the archbar trucks for a more authentic look.

HOe Heeresfeldbahn Diesel tankwagon
Used in first world war to supply Diesel to the narrow gauge loco's used at the warfront.

Roco or Eggerbahn Compatible!
Scale: H0e

Parts required to complete model:
1 set of Wheels:  Fleischmann 20024 or Roco 20024, available at your local model train store
You need a piece of 0,5mm brass wire and the Jig for H0e couplings http://shpws.me/4gY4 to create couplings.

This is a H0 Scale Model of an NSB Skb 202 Skiftetraktor. The model has printed wheelsets so it can be assembled for static display, or you can omit the wheelsets and have a working model, if you can find a motor and chassis small enough!

A 1 piece body kit for a Letterkenny and Burtonport Extension Railway all third or composite coach. Bogies available separately. Photos above show the prototype model when painted. For further details of this and other forthcoming projects, please see my website:

http://www.glr3dmodeldesign.co.uk/

Wheels for these models are now available via the link below:

http://www.ebay.co.uk/itm/12mm-gauge-coach-wheels-glr3dmodeldesign-coach-kit-/130559744352?pt=UK_Trains_Railway_Models&hash=item1e65f79960

Many thanks for looking!