by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
Dotsan
No1 in the series of animal heads, a smaller version of the 570mm high Stag Head (which is not available on Shapeways)
There is also a 75mm version here and a 300mm version here
The Animal Head Collection.
No 2 is a Zebra.
No 3 is a Rhino.
No 4 is a Tiger.
Tiger Head 2.
No 5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination.
Please send your pictures and share your thoughts on the design.
There is also a 75mm version here and a 300mm version here
The Animal Head Collection.
No 2 is a Zebra.
No 3 is a Rhino.
No 4 is a Tiger.
Tiger Head 2.
No 5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination.
Please send your pictures and share your thoughts on the design.
by
Dotsan
No2 in the series of 3D printed animal heads.
The Animal Head Collection.
No 1 is a Stag head.
There is also a 75mm version here and a 300mm version here
No 3 is a Rhino.
No 4 is a Tiger.
Tiger Head 2.
5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination. The Zebra head works well, I've concentrated on only printing the black parts leaving the white empty. It is available in BSF and WSF. Both materials tell a different story.
Please send your pictures and share your thoughts on the design.
The Animal Head Collection.
No 1 is a Stag head.
There is also a 75mm version here and a 300mm version here
No 3 is a Rhino.
No 4 is a Tiger.
Tiger Head 2.
5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination. The Zebra head works well, I've concentrated on only printing the black parts leaving the white empty. It is available in BSF and WSF. Both materials tell a different story.
Please send your pictures and share your thoughts on the design.
by
Dotsan
No 3 in the series of 3D printed animal heads.
The Animal Head Collection.
No 1 is a Stag Head.
There is also a 75mm version here and a 300mm version here
No 2 is a Zebra.
No 4 is a Tiger.
Tiger Head 2.
5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination.
The Rhino head works well for reducing printing cost, it is available in BSF and WSF. Both materials tell a different story.
Please send your pictures and share your thoughts on the design.
The Animal Head Collection.
No 1 is a Stag Head.
There is also a 75mm version here and a 300mm version here
No 2 is a Zebra.
No 4 is a Tiger.
Tiger Head 2.
5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination.
The Rhino head works well for reducing printing cost, it is available in BSF and WSF. Both materials tell a different story.
Please send your pictures and share your thoughts on the design.
by
QUATRO
Companion Cube storage box
Dimensions:
> Storage compartment (inner space): 30x30x30mm
> Outer maximum boundaries: 43x43x43mm
Other sizes and prices available on my store!
From the creator of the well-known GLaDOS ring comes a brand new accessory that is sure to be turning heads of those who see it - the Companion Cube storage box!
If you are a Portal geek like me - you know that the Companion Cube is basically a loveable version of Aperture Science Weighted Storage Cube. So if it's a storage cube - why not store something in it!
This little buddy is perfect for stashing your favorite pice(s) of jewelry or other small nick-knacks in style. Maybe it could even become a box for an engagement ring...?
The cube's corners reach up to ~6.4mm in thickness and the walls are as thick as ~3mm, so you are guaranteed that the cube will withstand rough conditions!
\ The actual product may not look like in the presented pictures - it comes in a single color, depending on the material you've chosen from the material list to the right! If you select durable plastic material, it is perfect for painting if you so desire :)
Please also check out other products on my store and do not hesitate to contact me if you have any questions!
Dimensions:
> Storage compartment (inner space): 30x30x30mm
> Outer maximum boundaries: 43x43x43mm
Other sizes and prices available on my store!
From the creator of the well-known GLaDOS ring comes a brand new accessory that is sure to be turning heads of those who see it - the Companion Cube storage box!
If you are a Portal geek like me - you know that the Companion Cube is basically a loveable version of Aperture Science Weighted Storage Cube. So if it's a storage cube - why not store something in it!
This little buddy is perfect for stashing your favorite pice(s) of jewelry or other small nick-knacks in style. Maybe it could even become a box for an engagement ring...?
The cube's corners reach up to ~6.4mm in thickness and the walls are as thick as ~3mm, so you are guaranteed that the cube will withstand rough conditions!
\ The actual product may not look like in the presented pictures - it comes in a single color, depending on the material you've chosen from the material list to the right! If you select durable plastic material, it is perfect for painting if you so desire :)
Please also check out other products on my store and do not hesitate to contact me if you have any questions!
by
MichaelMueller
This is a full working tabacco pipe. The head is made with glazed ceramics, the mouthpiece is antique bronze glossy.
+ 
A pipe is definitely a matchmaker. It makes you look distinguished and sexy. Like a successful scientist, a confident playboy or an experienced sailor.
Yeah, tabacco is bad for your health, so use bubbles instead! Works even better cause it gives you a great lemon flavour, but this depends on the dish soap you use. The ladys will appreciate it!
Attention!
The pipe is made of two parts. You need to order both and mount it by yourself! You can find the mouthpiece here.
I would suggest e.g. Sugru (sugru.com) for the sealing.
Cause the pipe is made of glazed ceramic, there is the possibility that some of the glaze stuck the openings. In case of this, you need to grind or even drill this parts to clear it.
Please order the pipe only if you think you can handle this!
Please message me if you have any questions.
+
A pipe is definitely a matchmaker. It makes you look distinguished and sexy. Like a successful scientist, a confident playboy or an experienced sailor.
Yeah, tabacco is bad for your health, so use bubbles instead! Works even better cause it gives you a great lemon flavour, but this depends on the dish soap you use. The ladys will appreciate it!
Attention!
The pipe is made of two parts. You need to order both and mount it by yourself! You can find the mouthpiece here.
I would suggest e.g. Sugru (sugru.com) for the sealing.
Cause the pipe is made of glazed ceramic, there is the possibility that some of the glaze stuck the openings. In case of this, you need to grind or even drill this parts to clear it.
Please order the pipe only if you think you can handle this!
Please message me if you have any questions.
