by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
curvecreative
Nanolet
Everyone's wearing their Nano on their wrist nowadays, now you can wear it on a one part 3D printed nano bracelet.
The NANOLET simply wraps around your wrist and fits snugly up to your hand which is perfect for running and everyday use. An alternative to the plethora of nano watches that are around now.
Featured on: Mashable , Cult of Mac , Yanko Design and many more.
Suitable for medium sized wrists. Available in a range of colors
Medium is for a wrist of circumference 165mm - 185mm. The best way to measure your wrist is to wrap a piece of string around your wrist, mark it and then measure it. Maximum wrist size is 190mm.
Unboxing Video here
Click here for OTHER SIZES
Click here to visit our site
Or click here to keep up to date on Facebook
Interested in buying Nanolets in BULK at reduced price? For LARGE , MEDIUM and SMALL
by
MichielCornelissen
Tool, symbol or both?
The bits on this pendant are based on actual bit sizes - including an IKEA standard tool - so 'a bit cross' can be used for light jobs. Just remember the steel isn't tempered like 'real' tool bits and tolerances may vary.
I recommend using it with a red leather cord of about 78 cm/ 31 inch.
If you are new to the Shapeways website: to order you will be asked to create an account (it's easy).
The bits on this pendant are based on actual bit sizes - including an IKEA standard tool - so 'a bit cross' can be used for light jobs. Just remember the steel isn't tempered like 'real' tool bits and tolerances may vary.
I recommend using it with a red leather cord of about 78 cm/ 31 inch.
If you are new to the Shapeways website: to order you will be asked to create an account (it's easy).
by
sevensheaven
A full-color, high-quality 3D-printed bust of the legendary, celebrated former Apple founder and CEO Steve Jobs, modeled and textured in a retro 3D pixel style by the Dutch Sevensheaven design studio.
Having this remarkable and unique gadget on your desk will undoubtedly make your friends and colleagues very jealous and earn you eternal respect.
Combine Steve Jobs with the also available Steve Wozniak bust to reunite the founding fathers of Apple on your desk.
Having this remarkable and unique gadget on your desk will undoubtedly make your friends and colleagues very jealous and earn you eternal respect.
Combine Steve Jobs with the also available Steve Wozniak bust to reunite the founding fathers of Apple on your desk.
by
MikeNaylor
A surprising arrangement of figures to create a mathematical form.
Please note that you must order TWO SETS to create the cube – each set includes two figures and four are necessary to create this sculpture. The figures are identical and snap together tightly hands to ankles to make this striking sculpture. Mix and match colors for your own effects. Or order more than two sets to experiment with other configurations.
This model is being exhibited at the Center for Arts Gallery at Towson University, June 30-July 28, 2012.
Please note that you must order TWO SETS to create the cube – each set includes two figures and four are necessary to create this sculpture. The figures are identical and snap together tightly hands to ankles to make this striking sculpture. Mix and match colors for your own effects. Or order more than two sets to experiment with other configurations.
This model is being exhibited at the Center for Arts Gallery at Towson University, June 30-July 28, 2012.
by
cinemo
This pencil and pen holder is made of first 500 digits of Pi (actually 546 exactly), the numbers are arranged along a spiral path. As you can see from the photos, the printing (Black Strong &Flexible) is very delicate and detailed. This desk accessory is both useful and decorative.
by
noesis
The CardCase is now customizable! See Below
The CardCase for the IPhone 4 does what other card carrying IPhone cases can do and then some!
The sleek, patent pending, snap-on case not only protects your IPhone, but can also replaces your wallet or current business card holder and the integrated card slot on the side allows you to use any available card as an instant stand in portrait or landscape mode! Perfect for watching movies on the go, Facetime chatting, or using your IPhone as an alarm clock!
The CardCase can comfortably hold 2 credit or ID cards, or 4-5 business cards, and works perfectly with either the AT&T or Verizon IPhone versions.
And the CardCase is now customizable! When ordering you can change the side text to anything you'd like up to 15 characters (company name, twitter username, real name etc.) you can also choose the text orientation and alignment.
Designed by Noesis Design Lab and manufactured by Shapeways, this durable nylon polyamide case has a unique look and grippy feel to help keep your IPhone (and cards) safe.
The case is shipped worldwide directly from Shapeways.
Available in a multitude of colors If you don't specify a color, the default is white
The CardCase for the IPhone 4 does what other card carrying IPhone cases can do and then some!
The sleek, patent pending, snap-on case not only protects your IPhone, but can also replaces your wallet or current business card holder and the integrated card slot on the side allows you to use any available card as an instant stand in portrait or landscape mode! Perfect for watching movies on the go, Facetime chatting, or using your IPhone as an alarm clock!
The CardCase can comfortably hold 2 credit or ID cards, or 4-5 business cards, and works perfectly with either the AT&T or Verizon IPhone versions.
And the CardCase is now customizable! When ordering you can change the side text to anything you'd like up to 15 characters (company name, twitter username, real name etc.) you can also choose the text orientation and alignment.
Designed by Noesis Design Lab and manufactured by Shapeways, this durable nylon polyamide case has a unique look and grippy feel to help keep your IPhone (and cards) safe.
The case is shipped worldwide directly from Shapeways.
Available in a multitude of colors If you don't specify a color, the default is white
by
JoshuaHarker
The Guy Fawkes mask that has become a symbol of solidarity among the anonymous 99% of the "Occupy" movement & an indelible icon in political & pop culture. Smallest size (1 inch) available in Silver at this scale. Features a ring on the back to wear as a necklace or hang as a pendant.
by
Bathsheba
It's a zero, and it's a one! This steel pendant IS geek chic.
by
nginear
This adapter allows for the continued use of the iPhone5 and Apple's universal dock or other accessories that use a standard universal dock connector plate. The Lightning to 30-pin Adapter from Apple is required.
In addition to allowing the use of older 30-pin accessories, it raises the iPhone to a comfortable height for using the phone while still docked. There is also a relief to provide easier access to the home button. Finally, the top surface of the adapter provides excellent leverage for removal of the iPhone from the dock.
by
Dotsan
A 5mm grided cube 50mm high.
It's a great desk toy for helping the creative juices.
The material it can be are restricted because of it size, please contact me with any questions?
by
paulbaut
Pick a time period in stock history, visualize the performance of the chosen stocks with a stock line chart diagram and use those lines as lead for the bracelet design.
This anti-subjective design solution questions the continuous obsession of the "genius" designer, the "form" generator by using a public economic network as source of pure form generation.
More information @ http://www.paulkweton.com/latest-projects/Embrace/
by
berky93
A small mobius strip charm that can be used as a pendant or as a keychain.
A mobius strip is a very unique shape because it defies conventional logic. It is a 3-dimensional object with only two faces. A single twist makes them flow from the outside to the inside and back again. Simple and elegant.
A mobius strip is a very unique shape because it defies conventional logic. It is a 3-dimensional object with only two faces. A single twist makes them flow from the outside to the inside and back again. Simple and elegant.
by
henryseg
Rectangular tube version. One arc's worth of fibers, from pole to pole.
by
swirlingbrain
This is a very small RBS. The ball was supposed to be attached to the top and to the side but the stick that attached it was so small it disappeared with printing. The rest of the sculpture arrived OK. I found the ball rolling around the bottom of the box. Hey, it works, though! Yea! See the video! http://www.youtube.com/watch?v=KGdUFg_X8mE
by
sevensheaven
A full-color, high-quality 3D-printed bust of Apple co-founder and tech wiz Steve 'Woz' Wozniak, modeled and textured in a retro 3D pixel style by the Dutch Sevensheaven design studio.
Having this remarkable and unique gadget on your desk will undoubtedly make your friends and colleagues very jealous and earn you eternal respect.
Combine Woz with the also available Steve Jobs bust to reunite the founding fathers of Apple on your desk.
by
susantio
The morning is uneventful until you pick up your espresso cup. To your horror, you find yourself holding the cup's ear, quite literally.
The ear comes pierced so you can decorate it with an earring. Earring not included.
The ear comes pierced so you can decorate it with an earring. Earring not included.
by
opresco
• 12 faceted die (based on the dodecahedron) • Could be worn as a pendant • Lanyard not included
See my New Spring Loaded Dice:
Spring-loaded 30-sided die.
Spring-loaded Icodie.
Spring-loaded die.
See my New Spring Loaded Dice:
Spring-loaded 30-sided die.
Spring-loaded Icodie.
Spring-loaded die.
by
virtox
Dodecahedron LED Cap
Material translucency test.
(example is WSF)
A cap for short 5 mm, high output leds.
Other shapes available on request (cubes, spheres, pyramids, you name it)
As startup-costs are half the price on this one, bulk is recommended, please contact me with the shape and amount required.
Material translucency test.
(example is WSF)
A cap for short 5 mm, high output leds.
Other shapes available on request (cubes, spheres, pyramids, you name it)
As startup-costs are half the price on this one, bulk is recommended, please contact me with the shape and amount required.
by
CLERCYSOPHIE
This candle holder can be used with real candle or led candle, be careful for lighting the candle to light it before installing it ...! there is a hole underneath for better handling. If you are interested by a special color that shapeways doesn't sell, send me a message, we can find a good solution!
let see other led candle holder on my web site:
http://www.photophoreandco.com/
let see other led candle holder on my web site:
http://www.photophoreandco.com/
by
Whystler
Here is a tower-like candelabra, which has a housing for an LED and coin battery (both supplied by purchaser). While the piece is lovely and interesting on its own, a shade is available, sold separately, in the shop to diffuse the light and provide more character.
Directions for assembly:
When you look at the housing where the coin battery slips in, you will notice that there are three supports that define this space. Two look the same, and one looks a little different. Let's call the one that looks different the "back support".
Get yourself an a standard 5mm LED. Any colour is good - your choice. For the brightest, I would recommend a super bright white or an ultra bright white. But for fun, know that blue and green LED's look very nice with the moon shade if you have bought it also :) Notice that one of the wires coming from the LED is longer. This is the "positive" wire.
Insert the wires of the LED down through the top hole in the candelabra, and wrap the "positive" wire around the "back support" taking care that it is placed so that it will only touch the battery at this place and no other.
Bend the other wire in a such a way that it will touch only the topside of the battery.
Get yourself a 2cm diameter, 3 volt coin battery. The ones I use are described by this code: CR2025. Insert this battery, negative side up, into the LED Candelabra housing.
Your Candelabra should immediately turn on nicely! Note that you can slide the battery slightly away from the back support and this will turn the light out.
If you have purchased the shade, this is very easy to twist on. Simply drop the shade down allowing its slots to slide over the three housing supports. Then twist the shade to secure it fits tightly.
Enjoy!
-Whystler
Directions for assembly:
When you look at the housing where the coin battery slips in, you will notice that there are three supports that define this space. Two look the same, and one looks a little different. Let's call the one that looks different the "back support".
Get yourself an a standard 5mm LED. Any colour is good - your choice. For the brightest, I would recommend a super bright white or an ultra bright white. But for fun, know that blue and green LED's look very nice with the moon shade if you have bought it also :) Notice that one of the wires coming from the LED is longer. This is the "positive" wire.
Insert the wires of the LED down through the top hole in the candelabra, and wrap the "positive" wire around the "back support" taking care that it is placed so that it will only touch the battery at this place and no other.
Bend the other wire in a such a way that it will touch only the topside of the battery.
Get yourself a 2cm diameter, 3 volt coin battery. The ones I use are described by this code: CR2025. Insert this battery, negative side up, into the LED Candelabra housing.
Your Candelabra should immediately turn on nicely! Note that you can slide the battery slightly away from the back support and this will turn the light out.
If you have purchased the shade, this is very easy to twist on. Simply drop the shade down allowing its slots to slide over the three housing supports. Then twist the shade to secure it fits tightly.
Enjoy!
-Whystler
by
sevensheaven
The classic old school Mario from the NES version of Super Mario Brothers, carefully translated to 3D pixels.
This is a separately orderable part from the Mariorama sculpture, which can also be found in the Sevensheaven 3D Print Store.
This is a separately orderable part from the Mariorama sculpture, which can also be found in the Sevensheaven 3D Print Store.
by
swirlingbrain
I've attached a ball to the rolling ball sculpture with the idea that you cut it off and sand it and it should work as the marble. The marble is 5/8 inch so it should work with regular glass or wooden marbles too. Yea it works! See the video!
by
cinemo
iPhone case that makes your iPhone looks like a Mac Pro.
I made this model which mimics the front of a MacPro computer for a friend of mine who is a fan of Apple products, I thought it might interest other geeks around there.
This phone cover has been tested for everyday use, the phone is set up and removed quickly, it fits nicely and all buttons and ports are easily accessible, no need to remove the case to plug the connector.
The model on the pictures was printed with the WSF polished material, I advise to use this material.
I made this model which mimics the front of a MacPro computer for a friend of mine who is a fan of Apple products, I thought it might interest other geeks around there.
This phone cover has been tested for everyday use, the phone is set up and removed quickly, it fits nicely and all buttons and ports are easily accessible, no need to remove the case to plug the connector.
The model on the pictures was printed with the WSF polished material, I advise to use this material.
by
PlainOrb
3D Printed and Tested.
It's used to seal the idling USB ports on your electronic devices, protecting them from dust, coffee / water spill etc. The plug part seals the USB port.
Please note:
USB ports must have 10mm horizontal or 7.5mm vertical clearance, if you want to use multiple plugs.
Specification:
* Made of nylon-12 ( View Material Property )
* Made by Shapeways.
* Worldwide shipping. ( View Shipping Cost )
More Product Photos in the Wild !!
Go to my shop 7Plain
Twitter @7Plain
All Rights Reserved.
It's used to seal the idling USB ports on your electronic devices, protecting them from dust, coffee / water spill etc. The plug part seals the USB port.
Please note:
USB ports must have 10mm horizontal or 7.5mm vertical clearance, if you want to use multiple plugs.
Specification:
* Made of nylon-12 ( View Material Property )
* Made by Shapeways.
* Worldwide shipping. ( View Shipping Cost )
More Product Photos in the Wild !!
Go to my shop 7Plain
Twitter @7Plain
All Rights Reserved.
by
opresco
«TRANSILVANIA» REMEMBERED
• One of several studies I made in preparation for a monumental project (on a much larger scale) entitled: «TRANSILVANIA REMEMBERED»; the project is about «TRANSILVANIA» (note the Romanian spelling) the quite famous Romanian passenger ship that was in continuous service from just before WW2 up to the end of Ceausescu's era in Romania; I happen to know a very interesting WW2 true story about events aboard this ship that could very easily be the script for a box office hit movie; more details about this project at a later date • The whole assembly comprising of the ANCHOR, with its CHAIN, leading through the bottle's neck to the floating SHIP inside the partially water-filled BOTTLE, were successfully printed together, as "one part", in White Strong and Flexible by Shapeways; the red ship is an identical copy of the one that is inside the bottle; it was printed separately in Terracotta Strong and Flexible to test its floating ability.
• One of several studies I made in preparation for a monumental project (on a much larger scale) entitled: «TRANSILVANIA REMEMBERED»; the project is about «TRANSILVANIA» (note the Romanian spelling) the quite famous Romanian passenger ship that was in continuous service from just before WW2 up to the end of Ceausescu's era in Romania; I happen to know a very interesting WW2 true story about events aboard this ship that could very easily be the script for a box office hit movie; more details about this project at a later date • The whole assembly comprising of the ANCHOR, with its CHAIN, leading through the bottle's neck to the floating SHIP inside the partially water-filled BOTTLE, were successfully printed together, as "one part", in White Strong and Flexible by Shapeways; the red ship is an identical copy of the one that is inside the bottle; it was printed separately in Terracotta Strong and Flexible to test its floating ability.
by
m_sill
Designed to sit on monitors, desks, books, windows, and anything with a 90* angle!
Let this little Robo-01 liven up your work area or dorm room. Chillin' to its own beat, Robo-01 encourages you to relax and turn the volume up. This is the first in a series of Desktop Buddies, please check back every now and then for more characters.
by
opresco
Click on PERSONALIZE to enter your own text, to replace "WALDO" (1-15 characters).
Dedicated to Waldo who's got exquisite taste in "Shot Glasses" ;-)
For playing Russian Roulette with your favorite Vodka, Coffee, Sake, Ouzo,
Tequila, Espresso, Chivas, Cappuccino, Pernod, and/or... Ice Cubes :-)
CAUTION: ALCOHOL & GUNS DON'T MIX!!!
Related Designs:
Dutch Soccer Shoe Universal "Shot Glass" :-)
Knitted Ceramics "Shot Glass"
Gun Barrel Universal "Shot Glass" ;-)
Dutch Shoe Universal "Shot Glass"
Got Monkey Wrench?
SATURN - Espresso & Sake Cup
Flying Saucer Espresso & Sake Cup
Espresso & Sake Finger Cup
Sake & Espresso Spiraling Tower Cup
Triangular Sake & Espresso Tower (Cup)
Rectangular Sake & Espresso Tower (Cup)
Sake Spring Cup #1
Sake Spring Cup #2
Sake Finger Cup #1
Sake Finger Cup #2
Sake Finger Cup #3
Sake Finger Cup #4
Sake Finger Cup #5
Sake Finger Cup #6
Sake Finger Cup #7
-------------------------------------------------------------------------
“The only way to discover the limits of the possible
is to go beyond them into the impossible.”
Arthur C. Clarke
Dedicated to Waldo who's got exquisite taste in "Shot Glasses" ;-)
For playing Russian Roulette with your favorite Vodka, Coffee, Sake, Ouzo,
Tequila, Espresso, Chivas, Cappuccino, Pernod, and/or... Ice Cubes :-)
CAUTION: ALCOHOL & GUNS DON'T MIX!!!
Related Designs:
Dutch Soccer Shoe Universal "Shot Glass" :-)
Knitted Ceramics "Shot Glass"
Gun Barrel Universal "Shot Glass" ;-)
Dutch Shoe Universal "Shot Glass"
Got Monkey Wrench?
SATURN - Espresso & Sake Cup
Flying Saucer Espresso & Sake Cup
Espresso & Sake Finger Cup
Sake & Espresso Spiraling Tower Cup
Triangular Sake & Espresso Tower (Cup)
Rectangular Sake & Espresso Tower (Cup)
Sake Spring Cup #1
Sake Spring Cup #2
Sake Finger Cup #1
Sake Finger Cup #2
Sake Finger Cup #3
Sake Finger Cup #4
Sake Finger Cup #5
Sake Finger Cup #6
Sake Finger Cup #7
-------------------------------------------------------------------------
“The only way to discover the limits of the possible
is to go beyond them into the impossible.”
Arthur C. Clarke
by
Heng
Send me the name you want, price includes LED and Powersupply. Price varies on Lettersize and number.
