This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
All the elements from the level are there: every mushroom, turtle, cloud and star. They are all carved out of the surface at different heights, which looks fantastic when you have a light coming from the side, and each block casts a shadow.
It's a great piece to have on your desk, or to hang from a string to let it spin around.
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
An espresso cup specially designed with fins, to ensure the successful deployment of your rocket fuel. All systems are go! Paraboloid bowl holds approximately 1.5 fl oz. or 45 mL. (Note that I previously claimed the cup held 60 mL. While my 3D modelling software still reports that as the internal volume, some combination of the printing process and glazing is robbing me of internal volume. Contact me if you'd be interested in a larger, more expensive 60 mL cup.)
After receiving feedback from Shapeways, I've created a slightly revised model for the cup. I'm told that this model will be easier to print and glaze, leading to a more reliable product. The changes are minor -- it's a little wider, a little heavier, and has more rounding on edges that were previously sharp (a 3D rendering shows the differences above).
Update (April 13th, 2013): The cup has had a great run on Shapeways, and I deeply appreciate the attention and positive feedback it has received. The bad news is that I've got to stop offering it for sale here. The good news is that the cup is now available commercially! It's being manufactured by Fred and Friends, sold under the name "Blast Off! Espresso Cup Set". It's already available for purchase online (perpetualkid.com, thinkgeek.com), and I'm sure you'll be able to find it in your favourite housewares store soon.
IMPORTANT:
The lamp consists of 2 parts, then you will receive 2 packages.... (open more info)...
one containing the 3D printed piece from Shapeways, and a Kit containing the bulb and stand from Veneridesign, then please contact me info@veneridesign.com for shipping address.
Thank you.
