by
RemivanOers
CLIP-IT for iPhone
Your charge buddy on the go.
Clip-it for iPhone converts your Euro iPhone charger to a wall dock; making sure that you can easily charge your phone at every wall socket. Unfurnished rooms, hotels and conference rooms are no longer a problem.
Clip-it lets you wind the usb cable easily around your charger while taking it with you.
Clip-it makes use of your existing Apple Dock Connector to USB Cable. Simply snap it in and lock the cable at the bottom. Clip-it is perfectly engineered to hold the latest two generations of original 30 pin Apple charging cables.
Clip-it is designed for the iPhone 4 & iPhone 4S and the included Apple USB Power Adapter (European version).
After all the excitement, an US version of Clip-it is available here!
Clip-it is manufactured by innovative 3D-printing in tough but lightweight polyamide. The surface has a fine texture. The product will be shipped in basic Shapeways packaging. Some powder residue from the 3D-printing process may be found on the product itself; if this is the case, it should be easy to clean off with small tooth sticks & brushes. When you ordered Clip-it in colour it might be wise to clean it with water under the tap, so the dyeing pigments that might still be on the product don’t colour your white Apple gadgets. For further information & support contact the Shapeways customer service.
Your charge buddy on the go.
Clip-it for iPhone converts your Euro iPhone charger to a wall dock; making sure that you can easily charge your phone at every wall socket. Unfurnished rooms, hotels and conference rooms are no longer a problem.
Clip-it lets you wind the usb cable easily around your charger while taking it with you.
Clip-it makes use of your existing Apple Dock Connector to USB Cable. Simply snap it in and lock the cable at the bottom. Clip-it is perfectly engineered to hold the latest two generations of original 30 pin Apple charging cables.
Clip-it is designed for the iPhone 4 & iPhone 4S and the included Apple USB Power Adapter (European version).
After all the excitement, an US version of Clip-it is available here!
Clip-it is manufactured by innovative 3D-printing in tough but lightweight polyamide. The surface has a fine texture. The product will be shipped in basic Shapeways packaging. Some powder residue from the 3D-printing process may be found on the product itself; if this is the case, it should be easy to clean off with small tooth sticks & brushes. When you ordered Clip-it in colour it might be wise to clean it with water under the tap, so the dyeing pigments that might still be on the product don’t colour your white Apple gadgets. For further information & support contact the Shapeways customer service.
by
Oatan
Clip used for the cable on headphones.
by
imperator
Own the Tesla Valve, as per the original design of Nikola Tesla, patented in 1920. See the video below to observe the valvular conduit in action.
Nikola Tesla invented this valvular conduit as a valve for his engines. Materials at the time were pretty bad, and valves were unreliable. Tesla figured that by removing any moving parts from a valving mechanism, he could create a simpler and more robust valve. The hook regions in the Tesla Valve reroute the fluid back in on itself creating a bit of resistance. All the hooks added together do a good job of arresting the fluid, especially when the gas or liquid is pulsed through the valvular conduit.
When you hold the valve in your hands after opening your shapeways package you are possessed of a strange kinship with the historical figure of Nikola Tesla. Pressing your lips to the valve, and blowing through it, you see that it actually works. In the resistive direction your breath is nullified to a mere whisper by the Tesla Valve. And in the non-resistive direction, air flows through unimpeded. It is startling the effect, and to think something so interesting as this valvular conduit was made so long ago.
I made this valve to commemorate Tesla's birthday on the 10th of July, 1856. Owning this valve is a way of recognizing a forgotten genius of unparralled creativity.
Nikola Tesla invented this valvular conduit as a valve for his engines. Materials at the time were pretty bad, and valves were unreliable. Tesla figured that by removing any moving parts from a valving mechanism, he could create a simpler and more robust valve. The hook regions in the Tesla Valve reroute the fluid back in on itself creating a bit of resistance. All the hooks added together do a good job of arresting the fluid, especially when the gas or liquid is pulsed through the valvular conduit.
When you hold the valve in your hands after opening your shapeways package you are possessed of a strange kinship with the historical figure of Nikola Tesla. Pressing your lips to the valve, and blowing through it, you see that it actually works. In the resistive direction your breath is nullified to a mere whisper by the Tesla Valve. And in the non-resistive direction, air flows through unimpeded. It is startling the effect, and to think something so interesting as this valvular conduit was made so long ago.
I made this valve to commemorate Tesla's birthday on the 10th of July, 1856. Owning this valve is a way of recognizing a forgotten genius of unparralled creativity.
by
imperator
Moving a turbine without any interfering veins? Only using smooth discs and adhesion with the air? The Tesla Turbine, made by Nikola Tesla, was certainly a marvel in its time. But this is no ordinary Tesla Turbine, but a Perez - Tesla Turbine.
The Tesla Turbine was made to be simple and elegant. Pressurized air entered through the periphery, circled about, and spiraled out of the center exit. And as it did it adhered to the smooth discs inside, pulling them and affecting rotary motion. However, the air, which had been following such a graceful path, would make a hard 90 degree turn when it exited the discs. The Perez - Tesla Turbine, available here, extends Tesla's design by using trumpet shaped discs, instead of Tesla's flat discs. This allows for an even smoother transition of the working fluid throughout the engine.
The axle mount for the turbine contains a fixture so that it can be mounted to a Lego Technic axle. Just blowing into the turbine, will cause this engine to rotate, though pressurized air can be used.
** Extreme caution must be used that this turbine not be driven so hard and fast, that it will disintegrate and pose a danger of flying shards. **
by
FreakyShape
Dock For The New iPhone 5 !
Because Apple has no plans to sell standalone dock for iPhone 5, I decided to create one. This dock is compatible with the lightning cable sold with the iPhone 5. You just need to put in place the lightning cable and to plug your iPhone!
Features :
- Works with the lightning cable
- Horizontal and vertical orientation
- iPhone speakers acces on the front
- Easy and quick system to place the lightning cable
You can also check out my iPhone 5 Cases :
iPhone 5 - vGraphene case iPhone 5 - Minimal bumper
Because Apple has no plans to sell standalone dock for iPhone 5, I decided to create one. This dock is compatible with the lightning cable sold with the iPhone 5. You just need to put in place the lightning cable and to plug your iPhone!
Features :
- Works with the lightning cable
- Horizontal and vertical orientation
- iPhone speakers acces on the front
- Easy and quick system to place the lightning cable
If you need further information, please don't hesitate to contact me.
You can also check out my iPhone 5 Cases :
iPhone 5 - vGraphene case iPhone 5 - Minimal bumper
by
SaGaDesign
The first of a series of fitness-inspired accessories from SaGa Design.
It is inspired by the Finnish concept of "Sisu", which roughly translates as "determination" or "grit". The design appears to defy gravity, with the human figure being much smaller than the device he is supporting.
Through this seemingly intense struggle, the device is forced upright and the design symbolizes the infinite determination each of us is capable of summoning to overcome hardship.
by
neotoy
http://www.youtube.com/watch?v=2KWUqXW6Z2w
by
VapourStudios
Curvestand for iPad
A versatile stand for your iPad and iPhone.
Works with ALL iPad models and works with iPhone 4/4s's.
Curvestand for iPad is fantastic for watching films on your iPad, or using as a second monitor at your desk for tweets or emails
Special edition orange iPad Curve Stand available only on www.curve.ie
Click here to keep up to date on Facebook
by
spruce
Many photographers lose there lenscap, especially me.
So it was time to solve this problem. With this cap holder you just click your lenscap in and are ready to go.
This holder is suitable for every 46mm lenscap I can design other holders for different diameters
If you can't find your size in my shop, please order the customizable version.
That version has a shapeways personalize option where you can request your diameter
