by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
thehiddenice
Each badge is about 1.25 x 1.25 x .25. If anyone is interested in Individual badges, let me know and I'll upload them separately.
More badges to come.
by
unellenu
Snowflake fractal pendant or decoration, pictured in white, strong and flexible.
This design looks beautiful worn as a pendant, and can also be hung as a tree ornament.
Dimensions of the pendant are cm:4.75 w x 4.908 d x 1.332 h / in:1.9 w x 1.9 d x 0.5 h (the dimensions of every Shapeways model are also on each page - near the bottom of the page).
The unellenu store on shapeways - for designer objects, fractal art, sculpture and jewelry.
shapeways.com/shops/unellenu
unellenu website
http://unellenu.com
twitter: unellenu
http://twitter.com/unellenu
facebook: unellenu jewellery
http://www.facebook.com/unellenu
facebook: unellenu sculpture and homewares
http://www.facebook.com/pages/Unellenu/188186071212813
http://www.youtube.com/unellenu1
by
ksimmons
This Seed of Life Pendant measures 1.7 inches tall and is available in a variety of materials.
http://mathworld.wolfram.com/SeedofLife.html
2010-12-20: Waiting for the first prints to arrive!
2010-12-21: Reoriented hoop on top.
2010-12-21: Ordered new revision, waiting for arrival.
2010-12-23: Prints cancelled due to small size. Reworking.
2011-01-23: This model is being updated with a larger, more functional clasp. Look for updates within the next couple days.
2011-01-26: This model has been revised with a new sturdier clasp.
2011-01-27: Test print ordered in stainless steel and alumide, expected arrival on February 16th.
2011-02-15: Alumide prints cancelled due to material limitations. Stainless Steel shipped.
2011-02-17: Stainless steel prints arrived and have been photographed.
2011-04-22: New photo uploaded.
http://mathworld.wolfram.com/SeedofLife.html
2010-12-20: Waiting for the first prints to arrive!
2010-12-21: Reoriented hoop on top.
2010-12-21: Ordered new revision, waiting for arrival.
2010-12-23: Prints cancelled due to small size. Reworking.
2011-01-23: This model is being updated with a larger, more functional clasp. Look for updates within the next couple days.
2011-01-26: This model has been revised with a new sturdier clasp.
2011-01-27: Test print ordered in stainless steel and alumide, expected arrival on February 16th.
2011-02-15: Alumide prints cancelled due to material limitations. Stainless Steel shipped.
2011-02-17: Stainless steel prints arrived and have been photographed.
2011-04-22: New photo uploaded.
by
unellenu
Peacock pendant from the Spinnoloids collection, in sterling silver by unellenu, 7.7cm in size. A larger size , 10cm is also available.
unellenu website
http://unellenu.com
The unellenu store on shapeways
http://www.shapeways.com/shops/unellenu
twitter: unellenu
http://twitter.com/unellenu
facebook: unellenu jewellery
http://www.facebook.com/unellenu
facebook: unellenu sculpture and homewares
http://www.facebook.com/pages/Unellenu/188186071212813
youtube: unellenu
http://www.youtube.com/unellenu1
Janelle Dehanne Wilson
by
virtox
A spiraling web cube
The cube contains 24 spirals intertwining.
A large, playful and decorative piece.
See video for full effect!
The cube contains 24 spirals intertwining.
A large, playful and decorative piece.
See video for full effect!
by
virtox
A double caged pendant with a few twists!
It contains an ambigram, made from two characters of your choosing.
The outer cage is connected to the ambigram,
which can rotate freely around the inner cage. (See the video!)
The used font is "Deja Vu Sans Mono".
I will do my very best to make each combination into a nice ambigram and make it fit snuggly inside the cage.
Leave a "remark for the designer" if you wish to see the model before I finalize your version.
It is also possible to use any symbol, model, logo you like, contact me with details and I'll make it happen!
I will add more examples over time.
Necklace not included.
It contains an ambigram, made from two characters of your choosing.
The outer cage is connected to the ambigram,
which can rotate freely around the inner cage. (See the video!)
The used font is "Deja Vu Sans Mono".
I will do my very best to make each combination into a nice ambigram and make it fit snuggly inside the cage.
Leave a "remark for the designer" if you wish to see the model before I finalize your version.
It is also possible to use any symbol, model, logo you like, contact me with details and I'll make it happen!
I will add more examples over time.
Necklace not included.
by
ksimmons
This Double Heptagram Pendant measures 1.6 inches tall.
http://en.wikipedia.org/wiki/Heptagram
2010-12-21: This model has not yet been printed.
2010-12-21: Ordered first prints, waiting for arrival.
2011-01-23: This model is being updated with a larger, more functional clasp. Look for updates within the next couple days.
2011-01-26: This model has been revised with a new clasp that will require a jump-ring to pass a cord through.
2011-01-27: Test print ordered in stainless steel and alumide, expected arrival on February 16th.
2011-02-15: Alumide prints cancelled due to material limitations. Stainless Steel shipped.
2011-02-17: Stainless steel prints arrived and have been photographed.
2011-03-07: Updated model with a rounded clasp. Photo depicts old clasp.
2011-04-22: New photo uploaded (still depicts old non-circular clasp, updates soon)
http://en.wikipedia.org/wiki/Heptagram
2010-12-21: This model has not yet been printed.
2010-12-21: Ordered first prints, waiting for arrival.
2011-01-23: This model is being updated with a larger, more functional clasp. Look for updates within the next couple days.
2011-01-26: This model has been revised with a new clasp that will require a jump-ring to pass a cord through.
2011-01-27: Test print ordered in stainless steel and alumide, expected arrival on February 16th.
2011-02-15: Alumide prints cancelled due to material limitations. Stainless Steel shipped.
2011-02-17: Stainless steel prints arrived and have been photographed.
2011-03-07: Updated model with a rounded clasp. Photo depicts old clasp.
2011-04-22: New photo uploaded (still depicts old non-circular clasp, updates soon)
by
unellenu
A sculptural geometric flower design which can be worn as a pendant ; thread a chain or cord through one of the petals
Some of the images above show the design in 'transparent detail' material.
The unellenu store on shapeways - for designer objects, fractal art, sculpture and jewelry.
shapeways.com/shops/unellenu
unellenu website unellenu.com
twitter: unellenuhttp://twitter.com/unellenu
facebook : unellenu jewellery
http://www.facebook.com/unellenu
facebook: unellenu fractal sculpture & homewares
http://www.facebook.com/pages/Unellenu/188186071212813
youtube: unellenuhttp://www.youtube.com/unellenu1
View a youtube video of this design
Some of the images above show the design in 'transparent detail' material.
The unellenu store on shapeways - for designer objects, fractal art, sculpture and jewelry.
shapeways.com/shops/unellenu
unellenu website unellenu.com
twitter: unellenuhttp://twitter.com/unellenu
facebook : unellenu jewellery
http://www.facebook.com/unellenu
facebook: unellenu fractal sculpture & homewares
http://www.facebook.com/pages/Unellenu/188186071212813
youtube: unellenuhttp://www.youtube.com/unellenu1
View a youtube video of this design
by
StBerlin
StBerlin presents a new dimension of Jewerly.
The magic cross - put the magic in your life.
by
unellenu
Spinnoloids Radiant Pendant 9.5cm in sterling silver by unellenu. Also available in a smaller size.
unellenu website http://unellenu.com/
facebook : unellenu jewellery
http://www.facebook.com/unellenu
facebook: unellenu fractal sculpture & homewares
http://www.facebook.com/pages/Unellenu/188186071212813
youtube: unellenu http://www.youtube.com/unellenu1
The unellenu store on shapeways - for designer objects, fractal art, sculpture and jewelry.
shapeways.com/shops/unellenu
unellenu website http://unellenu.com/
twitter: unellenu http://twitter.com/unellenu
facebook : unellenu jewellery
http://www.facebook.com/unellenu
facebook: unellenu fractal sculpture & homewares
http://www.facebook.com/pages/Unellenu/188186071212813
youtube: unellenu http://www.youtube.com/unellenu1
