by
MarcoA
My case for Raspberry Pi computer. To be assembled with the "LED lightguide" model nr. 486757 (http://shpws.me/6yFP).
This is the case everyone is talking about! ;)
Features: snap-fit fixing system for the board, easy to mount/unmount; snap-fit closing system, no screw required; bottom holes for blocking the computer by screws (sliding mount); led lightguides (not included in this model, available here: http://shpws.me/6yFP ); pre-shaped hole for GPIO access, just cut it out to open.
In this page you can find a gallery of shots working cases by enthusiast users!
http://marcoalici.wordpress.com/raspberry-pi-case-gallery/
by
GothamSmith
Bicycle Chainring Cufflinks perfect for use in a French cuff shirt.
by
MichielCornelissen
The Wrap is an accessory that attaches to the USB end of your iPhone charger, transforming it into a handy little cable winder for the charging cord.
This version of The Wrap works with recent US iPhone chargers and USB cables as shown in the images, up to those of iPhone 4 and iPhone 4S - please check before you purchase. There is currently no version of The Wrap available for iPhone 5 cables. It may work with other countries’ iPhone chargers too, but only if the geometry is exactly the same as the US version as shown here.
This product was originally developed for the European version of the iPhone charger - that version can be found here. The Wrap is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Colors may vary - please check in the 'select material' section above for the latest versions. Some powder residue from the printing process may be left on the product; if that's the case, it should be easy to clean off. Product is shipped in standard Shapeways packaging.
You can have a look at all the products in my shop here. Shipping rates are flat, so you could divide them over several products. If you have any feedback or questions on this product, please feel free to e-mail me directly at michiel(at)michielcornelissen(dot)com. If you like, follow me on twitter.
A wholesale offer of 8 units of The Wrap at reduced prices is now available here.
This version of The Wrap works with recent US iPhone chargers and USB cables as shown in the images, up to those of iPhone 4 and iPhone 4S - please check before you purchase. There is currently no version of The Wrap available for iPhone 5 cables. It may work with other countries’ iPhone chargers too, but only if the geometry is exactly the same as the US version as shown here.
This product was originally developed for the European version of the iPhone charger - that version can be found here. The Wrap is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Colors may vary - please check in the 'select material' section above for the latest versions. Some powder residue from the printing process may be left on the product; if that's the case, it should be easy to clean off. Product is shipped in standard Shapeways packaging.
You can have a look at all the products in my shop here. Shipping rates are flat, so you could divide them over several products. If you have any feedback or questions on this product, please feel free to e-mail me directly at michiel(at)michielcornelissen(dot)com. If you like, follow me on twitter.
A wholesale offer of 8 units of The Wrap at reduced prices is now available here.
by
chromoly
The Road Popper is a bike-mounted bottle opener that we developed for our own use and decided afterward to share. We designed it to fasten discreetly to the rails on the underside of the saddle to help keep your bike looking crisp. So far, it's worked on all the bottle caps we've tried it on. Material options are bronze infused stainless steel. Finish options are plain (on the right in the photograph), matte gold, glossy gold, matte antique bronze, and glossy antique bronze. The Road Popper is not intended for alcoholic beverages. Chromoly does not condone cycling while under the influence of alcohol.
Things You'll Need for Installation (not included with purchase)
2 - 3/8” long #6 flat head (countersunk) screws
2 - Nylon locknuts
1 - Screwdriver
1 - Needle nose pliers
Bike Requirements
Conventional bike saddle. If you're not sure if your seat is standard or not, give it a measure. The rails should be 7 mm's (0.275 inch) in diameter and roughly 44mm's (1.73 inch) apart.
At least 228mm's (9”) of space between the underside of your seat and your tire.
9mm's (3/8”) of open rail behind where the seat attaches to the seat post.
*Because this product is fabricated to order it is more expensive that it would be under normal manufacturing conditions. For this same reason it takes about 14 working days to arrive. The cost of shipping (via UPS) is included in the list price. Please note that duties and taxes may be applied to your order when it enters your country.
Things You'll Need for Installation (not included with purchase)
2 - 3/8” long #6 flat head (countersunk) screws
2 - Nylon locknuts
1 - Screwdriver
1 - Needle nose pliers
Bike Requirements
Conventional bike saddle. If you're not sure if your seat is standard or not, give it a measure. The rails should be 7 mm's (0.275 inch) in diameter and roughly 44mm's (1.73 inch) apart.
At least 228mm's (9”) of space between the underside of your seat and your tire.
9mm's (3/8”) of open rail behind where the seat attaches to the seat post.
*Because this product is fabricated to order it is more expensive that it would be under normal manufacturing conditions. For this same reason it takes about 14 working days to arrive. The cost of shipping (via UPS) is included in the list price. Please note that duties and taxes may be applied to your order when it enters your country.
