by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
MichielCornelissen
Important notice: a lot of people have been very happy with this product, but, as can be read in some of the comments below, it's clear that this design is right on the edge of what Shapeways can produce to the right quality at this moment. If you buy it, there's a risk of having a less then perfect fit, colors can be different from what you see on the screen, and, depending on how you use your phone as well as the tolerances of the case, it has been reported that the polyamide material can give a sort of polishing/scratching effect on the metal rim of the phone (you can find descriptions online of how to remove these kind of blemishes, but it may still be annoying).
Shapeways has, in my experience, been very good with customer service on this item, so they'll be happy to either return your money or provide a new product if you would be one of the unlucky ones; but it's up to you if you want to run the risk that you may have to go through this process.
Essential protection for iPhone 4S and iPhone 4
Even though 4-4 may be the worlds lightest and smallest iPhone 4 case, it still provides great protection to the vulnerable edges of the iPhones' front and back covers - while all controls and connections remain accessible. Its slightly protruding profile helps prevent protect the glass when laying your phone down; using 4-4 can also help to avoid signal loss problems.
This bumper-style case may be combined with commercially available screen protectors. 4-4 is manufactured from tough and durable 3d printed polyamide; it has a slightly textured surface that gives you great grip on your phone. Available in white, black and limited edition colors - note that in white, the 3d printed material may get dirty more quickly - but you can (seriously!) dishwash this product, so that shouldn't be too much of a problem. The 4-4 case is designed to have a tight fit around for iPhone. To put the iPhone in the case, or take it out, start at one of the bottom corners, where there are no buttons. Colors in the images above are for reference only; please check under 'select material' to get the most up-to-date preview of currently available product colors. Product is shipped in basic Shapeways packaging.
4-4 fits the GSM and CDMA/Verizon versions of iPhone 4, as well as the new iPhone 4S.
A two pack of 4-4's in the same color is available at reduced prices here.
You can have a look at all the products in my shop here. Consider buying 4-4 together with The Wrap, a handy cable winder for the European iPhone charger.
If you have any questions or feedback on this product, please feel free to contact me directly via michiel(at)michielcornelissen(dot)com.
Shapeways has, in my experience, been very good with customer service on this item, so they'll be happy to either return your money or provide a new product if you would be one of the unlucky ones; but it's up to you if you want to run the risk that you may have to go through this process.
Essential protection for iPhone 4S and iPhone 4
Even though 4-4 may be the worlds lightest and smallest iPhone 4 case, it still provides great protection to the vulnerable edges of the iPhones' front and back covers - while all controls and connections remain accessible. Its slightly protruding profile helps prevent protect the glass when laying your phone down; using 4-4 can also help to avoid signal loss problems.
This bumper-style case may be combined with commercially available screen protectors. 4-4 is manufactured from tough and durable 3d printed polyamide; it has a slightly textured surface that gives you great grip on your phone. Available in white, black and limited edition colors - note that in white, the 3d printed material may get dirty more quickly - but you can (seriously!) dishwash this product, so that shouldn't be too much of a problem. The 4-4 case is designed to have a tight fit around for iPhone. To put the iPhone in the case, or take it out, start at one of the bottom corners, where there are no buttons. Colors in the images above are for reference only; please check under 'select material' to get the most up-to-date preview of currently available product colors. Product is shipped in basic Shapeways packaging.
4-4 fits the GSM and CDMA/Verizon versions of iPhone 4, as well as the new iPhone 4S.
A two pack of 4-4's in the same color is available at reduced prices here.
You can have a look at all the products in my shop here. Consider buying 4-4 together with The Wrap, a handy cable winder for the European iPhone charger.
If you have any questions or feedback on this product, please feel free to contact me directly via michiel(at)michielcornelissen(dot)com.
by
MichielCornelissen
The product at this page is the PadFoot model that fits perfectly to iPad 2 as well as the 3d and 4th generation iPad. For PadFoot for iPad 1, go here.
PadFoot, the popular viewing stand for iPad, is now available for iPad 2 and the 3d and 4th generation iPad.
PadFoot clips to the corner of your iPad and will securely stand it upright in both landscape and portrait mode. It’s great for watching movies, clips and slideshows, for making FaceTime calls, as well as for use in presentations and (shop) displays.
At just 10 grams, PadFoot is now even lighter and smaller than its predecessor, with an increased viewing angle for even more viewing comfort - while it’s as stable and sturdy as ever.
Price information
The prices of PadFoot have been reduced by up to 20%. If you like, you can save shipping costs by combining this product with another product, like the ones from my shop; or just browse the galleries. A wholesale pack of 4 PadFoots, at up to 30% lower prices, is available here.
General information
PadFoot is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Check the materials section of this website for more information. Colors are seasonal; current availability is shown at the bottom of this page - this may be different from the colors shown in the images above. Each product ordered is individually manufactured, just for you. If you are new to the Shapeways site: to order, you'll be asked to create an account (it's easy; you can even log in with Facebook or Twitter).
It's best to use PadFoot on a stable and horizontal surface. Always make sure that your iPad is placed all the way into the opening in PadFoot; resting the iPad on one of its two edges without buttons. PadFoot will only work if your iPad has no cover on it. Product ships in basic Shapeways packaging. For more information, visit www.michielcornelissen.com; if you have any feedback or questions on this item, please feel free to contact me directly at michiel (at) michielcornelissen.com.
Some of the reactions on PadFoot, when it was introduced:
“PadFoot - Finally an iPad stand I can settle on. The iPad stands up perfectly, and there is absolutely no wobble or shake... PadFoot is also absolutely great to watch movies on the iPad...”
smokingapples.com
“... I was surprised by how small and lightweight it was... the PadFoot is extremely portable... PadFoot will hold the iPad securely at an angle perfect for viewing slide shows or videos.”
the-gadgeteer.com
“This Little iPad Stand Can Still Do a Lot of Standing... The PadFoot does the job and stays out of the way.”
gizmodo.com
PadFoot: one of fastcodesign’s most wanted products...
fastcodesign.com
“... I think the PadFoot... is just the perfect partner for the iPad”
gizmodiva.com
“ Simple yet adorable: The PadFoot iPad stand. At first, I thought the iPad’s inherent lack of stand was a flaw... Now I’m kind of happy that the tablet didn’t come with one. Otherwise, we wouldn’t have cute little items like this...”
todaysiphone.com
“... the Padfoot, a minuscule, efficient iPad stand that is beautiful in its simplicity.”
freshbump.com
“We’ve seen quite a few iPad stands since it hit the market, but the Padfoot by Dutch designer Michiel Cornelissen is just a bit better than what I’ve seen so far... Perfect!”
minimalissimo.com
“Padfoot ist einfach und genial.”
stilsucht.de
Padfoot on NOTCOT
notcot.org
“Received my PadFoot. Works great!”
Robert, New York
...bought a PadFoot... Best iPad accessory ever! You won’t be sorry, it is so light... I love it.
‘xultar’
“Just got my beautifully minimal PadFoot iPad stand from Michiel Cornelissen. Nice!”
‘mr_phillip’, Scotland
“I’ve bought many accessories for iPad, but PadFoot is by far the most useful one I’ve come across. Simple, qualitative and ingenious.”
Mario, The Netherlands
PadFoot, the popular viewing stand for iPad, is now available for iPad 2 and the 3d and 4th generation iPad.
PadFoot clips to the corner of your iPad and will securely stand it upright in both landscape and portrait mode. It’s great for watching movies, clips and slideshows, for making FaceTime calls, as well as for use in presentations and (shop) displays.
At just 10 grams, PadFoot is now even lighter and smaller than its predecessor, with an increased viewing angle for even more viewing comfort - while it’s as stable and sturdy as ever.
Price information
The prices of PadFoot have been reduced by up to 20%. If you like, you can save shipping costs by combining this product with another product, like the ones from my shop; or just browse the galleries. A wholesale pack of 4 PadFoots, at up to 30% lower prices, is available here.
General information
PadFoot is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Check the materials section of this website for more information. Colors are seasonal; current availability is shown at the bottom of this page - this may be different from the colors shown in the images above. Each product ordered is individually manufactured, just for you. If you are new to the Shapeways site: to order, you'll be asked to create an account (it's easy; you can even log in with Facebook or Twitter).
It's best to use PadFoot on a stable and horizontal surface. Always make sure that your iPad is placed all the way into the opening in PadFoot; resting the iPad on one of its two edges without buttons. PadFoot will only work if your iPad has no cover on it. Product ships in basic Shapeways packaging. For more information, visit www.michielcornelissen.com; if you have any feedback or questions on this item, please feel free to contact me directly at michiel (at) michielcornelissen.com.
Some of the reactions on PadFoot, when it was introduced:
“PadFoot - Finally an iPad stand I can settle on. The iPad stands up perfectly, and there is absolutely no wobble or shake... PadFoot is also absolutely great to watch movies on the iPad...”
smokingapples.com
“... I was surprised by how small and lightweight it was... the PadFoot is extremely portable... PadFoot will hold the iPad securely at an angle perfect for viewing slide shows or videos.”
the-gadgeteer.com
“This Little iPad Stand Can Still Do a Lot of Standing... The PadFoot does the job and stays out of the way.”
gizmodo.com
PadFoot: one of fastcodesign’s most wanted products...
fastcodesign.com
“... I think the PadFoot... is just the perfect partner for the iPad”
gizmodiva.com
“ Simple yet adorable: The PadFoot iPad stand. At first, I thought the iPad’s inherent lack of stand was a flaw... Now I’m kind of happy that the tablet didn’t come with one. Otherwise, we wouldn’t have cute little items like this...”
todaysiphone.com
“... the Padfoot, a minuscule, efficient iPad stand that is beautiful in its simplicity.”
freshbump.com
“We’ve seen quite a few iPad stands since it hit the market, but the Padfoot by Dutch designer Michiel Cornelissen is just a bit better than what I’ve seen so far... Perfect!”
minimalissimo.com
“Padfoot ist einfach und genial.”
stilsucht.de
Padfoot on NOTCOT
notcot.org
“Received my PadFoot. Works great!”
Robert, New York
...bought a PadFoot... Best iPad accessory ever! You won’t be sorry, it is so light... I love it.
‘xultar’
“Just got my beautifully minimal PadFoot iPad stand from Michiel Cornelissen. Nice!”
‘mr_phillip’, Scotland
“I’ve bought many accessories for iPad, but PadFoot is by far the most useful one I’ve come across. Simple, qualitative and ingenious.”
Mario, The Netherlands
by
TheoJansen
The third public evolution of the Animaris Geneticus Parvus. #7 has evolved legs, with pointy feet instead of flat. Featuring a fully working Theo Jansen mechanism as used in his work "the Rhinoceros".
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
by
TheoJansen
[Note: This propeller propulsion add-on does not include a 3D printed Strandbeest, which should be bought seperately! This propeller does not fit the Ondula version!]
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
by
Ammnra
Ring based on Portal 2 Wheatley
SIZE 6
Available in US Sizes 6-12 (in Half Sizes)
Click for Size 6
Click for Size 6.5
Click for Size 7
Click for Size 7.5
Click for Size 8
Click for Size 8.5
Click for Size 9
Click for Size 9.5
Click for Size 10
Click for Size 10.5
Click for Size 11
Click for Size 11.5
Click for Size 12
Due to material shrinkage, select one half size higher when ordering in Stainless Steel/Gold/Bronze
Actual Ring size is 0.3mm larger than diameter listed to account for ring width.
Click for US Sizes/Inner Dia
ATTENTION:The rings in the video/pics have been detail painted. The Shapeways parts will NOT be.
They will be one solid color.
Click for quick and easy detail painting guide
Thanks for your order and commitment to nerd culture!
SIZE 6
Available in US Sizes 6-12 (in Half Sizes)
Click for Size 6
Click for Size 6.5
Click for Size 7
Click for Size 7.5
Click for Size 8
Click for Size 8.5
Click for Size 9
Click for Size 9.5
Click for Size 10
Click for Size 10.5
Click for Size 11
Click for Size 11.5
Click for Size 12
Due to material shrinkage, select one half size higher when ordering in Stainless Steel/Gold/Bronze
Actual Ring size is 0.3mm larger than diameter listed to account for ring width.
Click for US Sizes/Inner Dia
ATTENTION:The rings in the video/pics have been detail painted. The Shapeways parts will NOT be.
They will be one solid color.
Click for quick and easy detail painting guide
Thanks for your order and commitment to nerd culture!
by
JoshuaHarker
The filigree design over the skull symbolizes ever growing renewal over the ghost of the past. Small silver version of the original design easily strung as a necklace.
by
izign
Impress with less.
Keep the shape pure or fill it up to match your daily fashion style.
This jewel can be easily customized just by placing a shiny wrinkled candy wrapper (not included).
This extravagant CLING has one size and is naturally hold in place between two fingers.
This jewel can give disposables a second and high value added life.
When interested in reselling please contact iZign for the resellers price list.
by
GothamSmith
For oenophiles and whiskey aficionados alike, a barrel, with a bung, on a chain.
Kegger charm comes in bronze finish, to better represent a nice woody grain. Necklace and jump ring separate.
by
burobruno
Same design as cross 05 only more massive. Therefore cross 01 is also available in metal, like in the picture.
by
burobruno
A bracelet in continuation of Ring_01. The bracelet is also structured in a 12 squared circle. Inner size is 63x63 mm.
by
Lightbringer
This is for making impressions on sealing wax in the form of the Shield Knot, an ancient symbol of protection according to Norse and Celtic traditions. I thought it an appropriate symbol to keep messages away from prying eyes.
The top of the handle is marked to make it much easier to align the impression and avoid setting it upside down or crooked.
Stainless steel versions of this seal are in stock and ready to ship in a few days through our Etsy Store - save a little money and get it much faster, no waiting for Shapeways to print!
Premium sealing wax can be ordered through our main website or Etsy Store.
Please use caution when working with fire and hot wax to avoid burns.
This symbol is also available as cufflinks.
The top of the handle is marked to make it much easier to align the impression and avoid setting it upside down or crooked.
Stainless steel versions of this seal are in stock and ready to ship in a few days through our Etsy Store - save a little money and get it much faster, no waiting for Shapeways to print!
Premium sealing wax can be ordered through our main website or Etsy Store.
Please use caution when working with fire and hot wax to avoid burns.
This symbol is also available as cufflinks.
by
woody64
This hat can be used as custom item for Minifigs. It's modelled according to drawings of Scott feather hats of Napoleonic wars.
