by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
NovastarDesign
Skyrim pendant
I made a pendant inspired from the The Imperial Symbol of the game Elder Scrolls V: Skyrim. I hope people who love this game also love this pendant. On the top of the wings are two holes, so you can wear it like a pendant. The pendant is double sided, both sides look the same. The picture shows the wrong way ;-0
I already have pictures of the pendant in stainless steel pictures in stainless steel
Also check out my Skyrim 'Dragonborn' ring Skyrim 'Dragonborn' ring.
The pendant is inspired on the game Elder Scrolls V Skyrim. The rights and intellectual property of the game belongs to Bethesda Softworks, which did a great job on creating the Elder Scrolls series.
I made a pendant inspired from the The Imperial Symbol of the game Elder Scrolls V: Skyrim. I hope people who love this game also love this pendant. On the top of the wings are two holes, so you can wear it like a pendant. The pendant is double sided, both sides look the same. The picture shows the wrong way ;-0
I already have pictures of the pendant in stainless steel pictures in stainless steel
Also check out my Skyrim 'Dragonborn' ring Skyrim 'Dragonborn' ring.
The pendant is inspired on the game Elder Scrolls V Skyrim. The rights and intellectual property of the game belongs to Bethesda Softworks, which did a great job on creating the Elder Scrolls series.
by
Rafalema
Now with removed support bars and SS as a new option!!
The hole is 1,2mm tall at highest point and 4mm wide at widest point to accommodate for more standard chains/strings.
Chain is not included!
A necklace/pendant inspired by the Assassin's Creed video game and book series'.
2.1cm wide and 2.9cm tall. 0.2cm thick.
Not an absolute replica of the creed symbol.
If you order one, please comment/review below.
Thank you for your time!
