by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
TheoJansen
The third public evolution of the Animaris Geneticus Parvus. #7 has evolved legs, with pointy feet instead of flat. Featuring a fully working Theo Jansen mechanism as used in his work "the Rhinoceros".
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
by
Whystler
The nocturnal (or nocturlabe) is a very old instrument for telling time at night by measuring the stars. While concept is ancient, this design is all original. It is fully functional (all dials move properly) and meant to be worn as a pendant. This is now available for sale, as it has been tested and works nicely.
How to Use the Nocturnal:
The top of the nocturnal is where you see a bit of a ring around a spike. This ring can be strung with a chain and makes it possible to wear the nocturnal as a pendant. When reading the nocturnal, this end of the piece should always be up.
Your first step is to set the outermost dial on the date. The months are shown as letters, with January and December at the top, and the progression of the months running *counterclockwise*. Note that the exact position of the letter actually marks the middle of that month. Look closer at the piece and you will see the line that separates the months between the letters.
Now, hold your nocturnal up to the starry night sky, making sure that the date is still properly set. Locate the North Star centred in the hole in the middle of the Nocturnal. Then use the central dial (the one that looks like a pointer) to point to the two stars at the end of the bowl of the *big* dipper.
Once you have this all set. Look closer at the pointer and you will see that within the pointer is an eliptical ring and within this is a smaller pointer. This smaller pointer points to a roman numeral, which shows you the time.
Note again, that the roman numeral is centred on the middle of the hour. So, if the little pointer points in the centre of the numeral, it is in fact half past.
So now you can tell time at night without a powered time piece. This is great for night owls, vampires, and those who appreciate a gothic or steampunk look.
How to Use the Nocturnal:
The top of the nocturnal is where you see a bit of a ring around a spike. This ring can be strung with a chain and makes it possible to wear the nocturnal as a pendant. When reading the nocturnal, this end of the piece should always be up.
Your first step is to set the outermost dial on the date. The months are shown as letters, with January and December at the top, and the progression of the months running *counterclockwise*. Note that the exact position of the letter actually marks the middle of that month. Look closer at the piece and you will see the line that separates the months between the letters.
Now, hold your nocturnal up to the starry night sky, making sure that the date is still properly set. Locate the North Star centred in the hole in the middle of the Nocturnal. Then use the central dial (the one that looks like a pointer) to point to the two stars at the end of the bowl of the *big* dipper.
Once you have this all set. Look closer at the pointer and you will see that within the pointer is an eliptical ring and within this is a smaller pointer. This smaller pointer points to a roman numeral, which shows you the time.
Note again, that the roman numeral is centred on the middle of the hour. So, if the little pointer points in the centre of the numeral, it is in fact half past.
So now you can tell time at night without a powered time piece. This is great for night owls, vampires, and those who appreciate a gothic or steampunk look.
by
TerraCotta
If M.C. Escher had owned fidget toys, he would have worn "One ring to rule the ball" as a pendant. A single, continuous line contains a small ball that makes orbit after mesmerizing orbit but cannot escape, always held down in four directions. Available in solid, durable stainless steel with optional antique bronze and gold plated finishes to fit any context, "One ring to rule the ball" now also includes a free rubber necklace so that you can confuse your mind any time the fancy strikes you! One customer echoes many others in saying, "I couldn't put it down. This thing is just too fun!"
Purchases by those gracious customers have now paid for the design time on this piece so it is available on a pay-what-you-want basis. Ordering from this page contributes 5$ towards continuing work such as the new, even more impossible "One ring to pwn the ball" (just released October 18th!) which can be found at http://www.shapeways.com/model/145172/one_ring_to_pwn_the_ball.html and the open-source "Ultimate Desk Toy" at http://www.shapeways.com/model/109166/ultimate_desk_toy.html . To download the original 3d file for your own use under a CC-BY license ( http://creativecommons.org/licenses/by/2.5/ca ) click "Download" at top right . To learn more about this design or other work from Terra Cotta, visit our website at http://www.terracottapf.com
Purchases by those gracious customers have now paid for the design time on this piece so it is available on a pay-what-you-want basis. Ordering from this page contributes 5$ towards continuing work such as the new, even more impossible "One ring to pwn the ball" (just released October 18th!) which can be found at http://www.shapeways.com/model/145172/one_ring_to_pwn_the_ball.html and the open-source "Ultimate Desk Toy" at http://www.shapeways.com/model/109166/ultimate_desk_toy.html . To download the original 3d file for your own use under a CC-BY license ( http://creativecommons.org/licenses/by/2.5/ca ) click "Download" at top right . To learn more about this design or other work from Terra Cotta, visit our website at http://www.terracottapf.com
by
byShapeways
Type in your text and we turn it into a customized metal branding iron.
Does not include the lighter.
The lighter is a BIC World, Classic, Maxi.
Want to make your own? Download the lighter attachment part here: http://www.shapeways.com/model/121517/ Do not flip/mirror the image, ie. please upload one you want as the actual result of the branding. If you have trouble uploading image like invalid file type, please make sure the filename has extension, for example, .jpg
Does not include the lighter.
The lighter is a BIC World, Classic, Maxi.
Want to make your own? Download the lighter attachment part here: http://www.shapeways.com/model/121517/ Do not flip/mirror the image, ie. please upload one you want as the actual result of the branding. If you have trouble uploading image like invalid file type, please make sure the filename has extension, for example, .jpg
by
Eeppium
A ring with crystals growing from it .
*Hole diameter 18,20mm* Size 8.
*It is recommended to add clear nailpolish to the innerparts, that are in contact with skin* See also the earrings to go with the ring Crystal Earring
*Hole diameter 18,20mm* Size 8.
*It is recommended to add clear nailpolish to the innerparts, that are in contact with skin* See also the earrings to go with the ring Crystal Earring
by
COVO
Product Name "Screwdriver Ring". Designed by Japan.
Available in either stainless steel (antique bronze & gold plated)
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
FORMA Laboratory Facebook Page!
Available in either stainless steel (antique bronze & gold plated)
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
FORMA Laboratory Facebook Page!
by
SiouX
remarkable Ring with belt-design.
Default size is 18.5 mm inner diameter.
I recommend (glossy) silver.
If you need a different ring-size, please click the personalize-button.
X-mas:
To check the time of delivery of your model, please see here:http://www.shapeways.com/holiday/planning
