by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
curvecreative
Nanolet
Everyone's wearing their Nano on their wrist nowadays, now you can wear it on a one part 3D printed nano bracelet.
The NANOLET simply wraps around your wrist and fits snugly up to your hand which is perfect for running and everyday use. An alternative to the plethora of nano watches that are around now.
Featured on: Mashable , Cult of Mac , Yanko Design and many more.
Suitable for medium sized wrists. Available in a range of colors
Medium is for a wrist of circumference 165mm - 185mm. The best way to measure your wrist is to wrap a piece of string around your wrist, mark it and then measure it. Maximum wrist size is 190mm.
Unboxing Video here
Click here for OTHER SIZES
Click here to visit our site
Or click here to keep up to date on Facebook
Interested in buying Nanolets in BULK at reduced price? For LARGE , MEDIUM and SMALL
by
TheoJansen
[Note: This propeller propulsion add-on does not include a 3D printed Strandbeest, which should be bought seperately! This propeller does not fit the Ondula version!]
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
by
Bathsheba
A theorem walks into a bar...
The Klein Bottle is a mathematical joke: a surface with only one side. This one feels just right in your hand and opens bottles with ease and style. Built to last in steel, it's the perfect touch for any math fan's kitchen.
The Klein Bottle is a mathematical joke: a surface with only one side. This one feels just right in your hand and opens bottles with ease and style. Built to last in steel, it's the perfect touch for any math fan's kitchen.
Yes, it really works!
Klein not-a-bottle-opener is here.
by
Dotsan
No1 in the series of animal heads, a smaller version of the 570mm high Stag Head (which is not available on Shapeways)
There is also a 75mm version here and a 300mm version here
The Animal Head Collection.
No 2 is a Zebra.
No 3 is a Rhino.
No 4 is a Tiger.
Tiger Head 2.
No 5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination.
Please send your pictures and share your thoughts on the design.
There is also a 75mm version here and a 300mm version here
The Animal Head Collection.
No 2 is a Zebra.
No 3 is a Rhino.
No 4 is a Tiger.
Tiger Head 2.
No 5 is an Elephant.
I'm experimenting with telling a story using minimal material to save on printing cost while inspiring the imagination.
Please send your pictures and share your thoughts on the design.
by
stop4stuff
Inspired by the well known mobius strip (discovered by August Ferdinand Möbius in 1858), an interest in the unusual, and 3D modelling, I created the Twin Rail mobius pendant.
A half shell and 3 rails form a bearing-like structure to encapsulate a train of 6mm balls in a mind-warping cage with a twisting, fascinating movement bringing to life the only pendent of its kind in the world.
Includes a 4mm loop for attaching to a necklace or leather cord.
See the photographs with retro-fitted 31 6mm chrome steel ball bearings... in the bottom photo, the balls have been heated until they 'blue'... check out the video to see how they move by clicking on the little icon below the camera above.
Also available smaller and in silver, Twin Rail Mobius Pendant - small
Note: this item is the shell alone, you will need to aquire and fit the balls (31 x 6mm or 29 x 1/4 in) as well as a suitable necklace to hang it from, a 3mm leather cord works well.
A half shell and 3 rails form a bearing-like structure to encapsulate a train of 6mm balls in a mind-warping cage with a twisting, fascinating movement bringing to life the only pendent of its kind in the world.
Includes a 4mm loop for attaching to a necklace or leather cord.
See the photographs with retro-fitted 31 6mm chrome steel ball bearings... in the bottom photo, the balls have been heated until they 'blue'... check out the video to see how they move by clicking on the little icon below the camera above.
Also available smaller and in silver, Twin Rail Mobius Pendant - small
Note: this item is the shell alone, you will need to aquire and fit the balls (31 x 6mm or 29 x 1/4 in) as well as a suitable necklace to hang it from, a 3mm leather cord works well.
by
Bathsheba
A sculpture. Contrary to popular belief, it is not an algorithmic object.
by
MichielCornelissen
The Wrap is an accessory that attaches to the USB end of your iPhone charger, transforming it into a handy little cable winder for the charging cord.
This version of The Wrap works with recent US iPhone chargers and USB cables as shown in the images, up to those of iPhone 4 and iPhone 4S - please check before you purchase. There is currently no version of The Wrap available for iPhone 5 cables. It may work with other countries’ iPhone chargers too, but only if the geometry is exactly the same as the US version as shown here.
This product was originally developed for the European version of the iPhone charger - that version can be found here. The Wrap is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Colors may vary - please check in the 'select material' section above for the latest versions. Some powder residue from the printing process may be left on the product; if that's the case, it should be easy to clean off. Product is shipped in standard Shapeways packaging.
You can have a look at all the products in my shop here. Shipping rates are flat, so you could divide them over several products. If you have any feedback or questions on this product, please feel free to e-mail me directly at michiel(at)michielcornelissen(dot)com. If you like, follow me on twitter.
A wholesale offer of 8 units of The Wrap at reduced prices is now available here.
This version of The Wrap works with recent US iPhone chargers and USB cables as shown in the images, up to those of iPhone 4 and iPhone 4S - please check before you purchase. There is currently no version of The Wrap available for iPhone 5 cables. It may work with other countries’ iPhone chargers too, but only if the geometry is exactly the same as the US version as shown here.
This product was originally developed for the European version of the iPhone charger - that version can be found here. The Wrap is manufactured in tough but lightweight, 3d printed polyamide with a fine surface texture. Colors may vary - please check in the 'select material' section above for the latest versions. Some powder residue from the printing process may be left on the product; if that's the case, it should be easy to clean off. Product is shipped in standard Shapeways packaging.
You can have a look at all the products in my shop here. Shipping rates are flat, so you could divide them over several products. If you have any feedback or questions on this product, please feel free to e-mail me directly at michiel(at)michielcornelissen(dot)com. If you like, follow me on twitter.
A wholesale offer of 8 units of The Wrap at reduced prices is now available here.
by
chromoly
The Road Popper is a bike-mounted bottle opener that we developed for our own use and decided afterward to share. We designed it to fasten discreetly to the rails on the underside of the saddle to help keep your bike looking crisp. So far, it's worked on all the bottle caps we've tried it on. Material options are bronze infused stainless steel. Finish options are plain (on the right in the photograph), matte gold, glossy gold, matte antique bronze, and glossy antique bronze. The Road Popper is not intended for alcoholic beverages. Chromoly does not condone cycling while under the influence of alcohol.
Things You'll Need for Installation (not included with purchase)
2 - 3/8” long #6 flat head (countersunk) screws
2 - Nylon locknuts
1 - Screwdriver
1 - Needle nose pliers
Bike Requirements
Conventional bike saddle. If you're not sure if your seat is standard or not, give it a measure. The rails should be 7 mm's (0.275 inch) in diameter and roughly 44mm's (1.73 inch) apart.
At least 228mm's (9”) of space between the underside of your seat and your tire.
9mm's (3/8”) of open rail behind where the seat attaches to the seat post.
*Because this product is fabricated to order it is more expensive that it would be under normal manufacturing conditions. For this same reason it takes about 14 working days to arrive. The cost of shipping (via UPS) is included in the list price. Please note that duties and taxes may be applied to your order when it enters your country.
Things You'll Need for Installation (not included with purchase)
2 - 3/8” long #6 flat head (countersunk) screws
2 - Nylon locknuts
1 - Screwdriver
1 - Needle nose pliers
Bike Requirements
Conventional bike saddle. If you're not sure if your seat is standard or not, give it a measure. The rails should be 7 mm's (0.275 inch) in diameter and roughly 44mm's (1.73 inch) apart.
At least 228mm's (9”) of space between the underside of your seat and your tire.
9mm's (3/8”) of open rail behind where the seat attaches to the seat post.
*Because this product is fabricated to order it is more expensive that it would be under normal manufacturing conditions. For this same reason it takes about 14 working days to arrive. The cost of shipping (via UPS) is included in the list price. Please note that duties and taxes may be applied to your order when it enters your country.
by
aeron203
A clock frozen in time, the Time Keeper commemorates a birth date, an anniversary, or any other significant moment in your life, in history, or the future. It will keep that time with perfect accuracy, forever. You set the date and time. You can also include a short message below the date.
UPDATE: The Time Keeper has been thickened 50% to ensure printability.
UPDATE: The Time Keeper has been thickened 50% to ensure printability.
by
Eeppium
A ring with crystals growing from it .
*Hole diameter 18,20mm* Size 8.
*It is recommended to add clear nailpolish to the innerparts, that are in contact with skin* See also the earrings to go with the ring Crystal Earring
*Hole diameter 18,20mm* Size 8.
*It is recommended to add clear nailpolish to the innerparts, that are in contact with skin* See also the earrings to go with the ring Crystal Earring
by
spruce
Many photographers lose there lenscap, especially me.
So it was time to solve this problem.
With this cap holder you just click your lenscap in and are ready to go.
This model is specially added to my shop for people who can't find there size.
So please make sure that your size isn't available in my shop before purchase this one.
Use the shapeways personalize option to send my your requested diameter.
So it was time to solve this problem.
With this cap holder you just click your lenscap in and are ready to go.
This model is specially added to my shop for people who can't find there size.
So please make sure that your size isn't available in my shop before purchase this one.
Use the shapeways personalize option to send my your requested diameter.
by
OneSaveSolutions
This chess set re-imagines the bodies of the traditional chess pieces to incorporate each piece's name as the focal point of their design.
It should be noted that each color/material must be ordered separately. This does, however allow for mixing and matching.
by
virtox
A hanging cup for your double espresso the morning after ;-)
It's in such a state that it cannot stand on it's own, so it really needs some support.
Luckily it has :-)
When you order, you will get the Hangover cup and the matching stand in glazed ceramics.
Printed Ceramics
With the current process, the round bottom on the cup will likely show some minor pits in the glazing from a small tripod it stands on during the baking.
And the bottom of the stand/saucer has rougher structure.
The rest of the glazing is fully covering, so it's safe to drink from.
Also available as a more sober version (standalone)
The cup is designed for a double espresso(60 ml), but can hold a maximum of about 90 ml.
Check out this photo of black version here
It's in such a state that it cannot stand on it's own, so it really needs some support.
Luckily it has :-)
When you order, you will get the Hangover cup and the matching stand in glazed ceramics.
Printed Ceramics
With the current process, the round bottom on the cup will likely show some minor pits in the glazing from a small tripod it stands on during the baking.
And the bottom of the stand/saucer has rougher structure.
The rest of the glazing is fully covering, so it's safe to drink from.
Also available as a more sober version (standalone)
The cup is designed for a double espresso(60 ml), but can hold a maximum of about 90 ml.
Check out this photo of black version here
by
thehiddenice
Each badge is about 1.25 x 1.25 x .25. If anyone is interested in Individual badges, let me know and I'll upload them separately.
More badges to come.
by
Kidmechano
Build and customize your own Action Bot!- Modular, upgradeable, figure kit- highly poseable, snap-fit, ball joint construction! **This figure includes both knife and sheath accessories.** You can see a video showing how the figure assembles in the product pictures embedded above and a turnable 3d viewer of the model at- http://skfb.ly/5k4hedcb Enjoy!
by
s_f_x
A beautiful translucent tea candle light which will look great on any table. The sleek and simple design goes well with many styles. The petals are quite thin to let the light through, yet the model is not overly fragile.
This light has been successfully tested with standard sized tea candles. However, as this model is made of plastic, use the usual safety precautions when using with candles and fire - never leave unattended, keep away from combustible material, and keep out of the hands of children.
This light has been successfully tested with standard sized tea candles. However, as this model is made of plastic, use the usual safety precautions when using with candles and fire - never leave unattended, keep away from combustible material, and keep out of the hands of children.
by
cinemo
This pencil and pen holder is made of first 500 digits of Pi (actually 546 exactly), the numbers are arranged along a spiral path. As you can see from the photos, the printing (Black Strong &Flexible) is very delicate and detailed. This desk accessory is both useful and decorative.
by
arthurditlef
ARTIFICIAL NATURE SERIES
Inspired by Nature, with an artificial twist.
Inspired by Nature, with an artificial twist.
by
printedCat
This piece of art was created in 3D software by "printedCat" 3D-designer in San Francisco, California, USA and
printed in nylon material by Shapeways.com in Holland or New York.
Enjoy watching!
All images are photos of real objects. "Proof Printed".
printedCat on Shapeways
printedCat.com
printedCat on Flickr
printedCat on YouTube
printedCat on Etsy
printedCat on Facebook
Enjoy watching!
All images are photos of real objects. "Proof Printed".
printedCat on Shapeways
printedCat.com
printedCat on Flickr
printedCat on YouTube
printedCat on Etsy
printedCat on Facebook
by
COVO
Product Name "Ring of the gamer". Designed by Japan.
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
FORMA Laboratory Facebook Page!
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
FORMA Laboratory Facebook Page!
by
aeron203
A clock frozen in time, the Time Keeper commemorates a birth date, an anniversary, or any other significant moment in your life, in history, or the future. It will keep that time with perfect accuracy, forever. You set the date and time. You can also include a short message below the date. The Time Keeper Pendant is 75% of the original size. 1.5 inches wide. UPDATE: The Time keeper has been thickened 50% to ensure printability.
by
MINGLES
A LEGO scaled version of Link's Cap, a piece of clothing featured in The Legend Of Zelda series.
by
HappenstanceHeroes
This little guy is a fox and proud of it.
This incarnation is best suited to use as a decorative object, but we're open to suggestions for how you'd like to see it modified for your use!
The two most interesting uses we've found so far are using the WSF (polished) version as a surprisingly striking little glow bulb if you shine a light inside it, and possibly using the (pleasantly hefty) stainless steel version as an imposing game board piece.
To the customer who recently ordered this in Antique Bronze Matte, we would love to hear from you as to how your order turns out! Please consider sharing a photo or your thoughts on it if you find the time. :)
This incarnation is best suited to use as a decorative object, but we're open to suggestions for how you'd like to see it modified for your use!
The two most interesting uses we've found so far are using the WSF (polished) version as a surprisingly striking little glow bulb if you shine a light inside it, and possibly using the (pleasantly hefty) stainless steel version as an imposing game board piece.
To the customer who recently ordered this in Antique Bronze Matte, we would love to hear from you as to how your order turns out! Please consider sharing a photo or your thoughts on it if you find the time. :)
by
Kidmechano
Breathe a bit of new life into your Xevoz collection! ModiBot X figure kit ver 2.0- build and customize your own Action Hero! Each figure kit is highly-poseable, modular, and upgradeable using a simple snap-fit, ball joint construction! ---- accepts many parts and accessories from Xevoz action figure kits using 6mm ball & socket and 4mm square peg system- UPDATE- New head, feet, and shin for improved fit and posability.
by
wpagnes82828
for iphone 4/4s.
The hollowed case in combination with the contract color of the iphone itself gives a vivid animal figure.
The case is stylish and in the same time heat eliminated.
by
curvecreative
Knotcase
A Celtic inspired iPhone case.
The KNOTCASE snaps onto your iPhone 4 or 4S and provides a slimline case that covers the back and sides of your phone. The Knot pattern on the back give an appealing texture to touch and gives your iPhone a unique look.
Click here to visit our site
Or click here to keep up to date on Facebook
by
abite
*Important: Rubber-sponge gaskets for preventing sound leakage are ready. If you have ordered this item, please PM or email me with your order information and address. jcho@abitedesign.com.
I will send you a couple of gaskets via airmail.
---------------------------------------------------
The Minimized Gramophone "iAcoustic S" is an accessory for your iPhone, but it was not intended for an additional, separate device.
You need the charging cable for the iPhone every day, and the iAcoustic S was designed to transform the cable into a multi-functional device. The cable dressed up with the iAcoustic S can become an acoustic amplifier and a stand as well as a charger. When you put the cable into your bag, the iAcoustic S can also be a cable winder.
Its design was simplified for following the additional functions, and to provice the longer vibrating air column for the better and louder sound quality, its curved tube shape was created. The thickness of its bell and curved tube is 0.8mm.
It can also fit the iPhone with a typical case or a bumper. A mock-up plug is included, so you can use it instead of the charging cable when you don't need the cable.
- Link for iPhone 4/4S version -
* It works with the original charging cable.
I will send you a couple of gaskets via airmail.
---------------------------------------------------
The Minimized Gramophone "iAcoustic S" is an accessory for your iPhone, but it was not intended for an additional, separate device.
You need the charging cable for the iPhone every day, and the iAcoustic S was designed to transform the cable into a multi-functional device. The cable dressed up with the iAcoustic S can become an acoustic amplifier and a stand as well as a charger. When you put the cable into your bag, the iAcoustic S can also be a cable winder.
Its design was simplified for following the additional functions, and to provice the longer vibrating air column for the better and louder sound quality, its curved tube shape was created. The thickness of its bell and curved tube is 0.8mm.
It can also fit the iPhone with a typical case or a bumper. A mock-up plug is included, so you can use it instead of the charging cable when you don't need the cable.
- Link for iPhone 4/4S version -
* It works with the original charging cable.
by
froland
Giraffe with partially open body through a Voronoi structure.
The body hosts two balls with a Voronoi structure, one inside the other.
Want to know more about Voronoi?
Voronoi on Wikipedia
See the shop for other Voronoi inspired models and jewlery.
The body hosts two balls with a Voronoi structure, one inside the other.
Want to know more about Voronoi?
Voronoi on Wikipedia
See the shop for other Voronoi inspired models and jewlery.
by
Kidmechano
ModiRaptor is the scourge of the ModiBot universe and 47 parts of poseable madness. Highly articulated tail and body. Vice-like jaws and 12 moving claws. Compatible with ModiBot hex-fit figures and accessories. What can you imagine and build with these parts? Here is a download link for an Instructions- https://www.dropbox.com/sh/s4vil011e6yh916/B6w8_cOWDB
by
vertigopolka
Here is a cubic interpretation of the classic trefoil torus knot.
There are also 50mm and 1-inch versions of this shape without the hanging loop.
Check out additional models of knots and torus knots in my Knots section, and see more of my pendants in my Pendants section.
There are also 50mm and 1-inch versions of this shape without the hanging loop.
Check out additional models of knots and torus knots in my Knots section, and see more of my pendants in my Pendants section.
by
i8kermit
Note: This is for one cufflink. Order 2 for a full set, unless you rock your own style!
For more on my designs, visit www.prero.com.
+
Want to get a set?
+ 
by
MacBurro
A Little SteamPunk World Model for Desk Decoration
