by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
QUATRO
Product Name "CLaDOS Ring". Designed by QUATRO.
Please note that this ring will come in a solid color/material! So please choose carefully! White plastic is good for DIY painting while steel and silver ones will shine your way to stardom :)
If you cannot find your size OR you just don't wear rings - try taking a look at my pendant!http://shpws.me/3NxX
Want to know more about the product?
Available in a variety of materials
The default size is ~20.32 mm in inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.) Please refer to sizes at this page.
Conversion chart for ring sizes:
US Ring Size - Inside diameter
8 - 18.1mm
9 - 19.0mm
10 - 19.8mm
11 - 20.6mm
12 - 21.4mm
13 - 22.2mm
I hope you like this piece as much as I do:)
Be sure to tell a friend! Shop more at:
http://www.shapeways.com/shops/uncleQUATRO :)
Please note that this ring will come in a solid color/material! So please choose carefully! White plastic is good for DIY painting while steel and silver ones will shine your way to stardom :)
If you cannot find your size OR you just don't wear rings - try taking a look at my pendant!http://shpws.me/3NxX
Want to know more about the product?
Available in a variety of materials
The default size is ~20.32 mm in inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.) Please refer to sizes at this page.
Conversion chart for ring sizes:
US Ring Size - Inside diameter
8 - 18.1mm
9 - 19.0mm
10 - 19.8mm
11 - 20.6mm
12 - 21.4mm
13 - 22.2mm
I hope you like this piece as much as I do:)
Be sure to tell a friend! Shop more at:
http://www.shapeways.com/shops/uncleQUATRO :)
by
Apathy
Portal''s Companion Cube with the heart modeled into it
by
Charmed_Life_Designs
A new twist on the classic "Halved heart" necklace. Give one to your sweetheart!
If you would like to order it in two different colors, the halves are available here:
1/2: www.shapeways.com/model/163395/
2/2: www.shapeways.com/model/163396/
If you would like to order it in two different colors, the halves are available here:
1/2: www.shapeways.com/model/163395/
2/2: www.shapeways.com/model/163396/
