by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
Bathsheba
A theorem walks into a bar...
The Klein Bottle is a mathematical joke: a surface with only one side. This one feels just right in your hand and opens bottles with ease and style. Built to last in steel, it's the perfect touch for any math fan's kitchen.
The Klein Bottle is a mathematical joke: a surface with only one side. This one feels just right in your hand and opens bottles with ease and style. Built to last in steel, it's the perfect touch for any math fan's kitchen.
Yes, it really works!
Klein not-a-bottle-opener is here.
by
virtox
You can't hold it forever!
Here is the corner stand for the 5cm Gyro the Cube.
Due to printing variations it might be a bit tight fit for some cubes.
I recommend any of the Strong & Flexible
Alumide available on request.
Here is the corner stand for the 5cm Gyro the Cube.
Due to printing variations it might be a bit tight fit for some cubes.
I recommend any of the Strong & Flexible
Alumide available on request.
by
MOLabs
A more than 100 year-old classic for your own desk, in a modern, improved version!
In 1869, Christian Wiener constructed the first model of a cubic surface with 27 lines (in plaster, by hand!). This achievement opened the way for many similar objects in the following couple of years.
One of the most famous of these is certainly the one of the Clebsch Diagonal Surface which had been studied by Alfred Clebsch. Its model was probably planned by Alfred Clebsch and Felix Klein. Compared to the historical model, our version has the advantage that it only shows the surface itself and not a large body of plaster material as a support which is not part of the surface and which distracts from the pure geometry of the surface.
Part of the aesthetics of our objects comes from the fact that we chose to represent the surface in such a way that the ratio between the height and the width of our object is the so-called golden ratio.
For more info see MO-Labs.com.
In 1869, Christian Wiener constructed the first model of a cubic surface with 27 lines (in plaster, by hand!). This achievement opened the way for many similar objects in the following couple of years.
One of the most famous of these is certainly the one of the Clebsch Diagonal Surface which had been studied by Alfred Clebsch. Its model was probably planned by Alfred Clebsch and Felix Klein. Compared to the historical model, our version has the advantage that it only shows the surface itself and not a large body of plaster material as a support which is not part of the surface and which distracts from the pure geometry of the surface.
Part of the aesthetics of our objects comes from the fact that we chose to represent the surface in such a way that the ratio between the height and the width of our object is the so-called golden ratio.
For more info see MO-Labs.com.
by
vertigopolka
Here's a 3-inch model consisting of a set of twelve interconnecting, colored pentagons; the exploded, twisted faces of a dodecahedron. See more of my color models: Vertigo's Colored Polyhedra
by
vertigopolka
Simply, six intertwined colored squares. Sort of a deconstructed cube. See more of my color models: Vertigo's Colored Polyhedra
