by
TheoJansen
The third public evolution of the Animaris Geneticus Parvus. #7 has evolved legs, with pointy feet instead of flat. Featuring a fully working Theo Jansen mechanism as used in his work "the Rhinoceros".
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
by
TheoJansen
[Note: This propeller propulsion add-on does not include a 3D printed Strandbeest, which should be bought seperately! This propeller does not fit the Ondula version!]
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
by
FreakyShape
Dock For The New iPhone 5 !
Because Apple has no plans to sell standalone dock for iPhone 5, I decided to create one. This dock is compatible with the lightning cable sold with the iPhone 5. You just need to put in place the lightning cable and to plug your iPhone!
Features :
- Works with the lightning cable
- Horizontal and vertical orientation
- iPhone speakers acces on the front
- Easy and quick system to place the lightning cable
You can also check out my iPhone 5 Cases :
iPhone 5 - vGraphene case iPhone 5 - Minimal bumper
Because Apple has no plans to sell standalone dock for iPhone 5, I decided to create one. This dock is compatible with the lightning cable sold with the iPhone 5. You just need to put in place the lightning cable and to plug your iPhone!
Features :
- Works with the lightning cable
- Horizontal and vertical orientation
- iPhone speakers acces on the front
- Easy and quick system to place the lightning cable
If you need further information, please don't hesitate to contact me.
You can also check out my iPhone 5 Cases :
iPhone 5 - vGraphene case iPhone 5 - Minimal bumper
by
RemivanOers
CLIP-IT for iPhone Lightning US
Your iPhone 5 charge buddy on the go.
Clip-it for iPhone converts your iPhone charger to a wall dock; making sure that you can easily charge your phone at every wall socket. Unfurnished rooms, hotels and conference rooms are no longer a problem.
Clip-it makes use of your new Apple Lightning Connector to USB Cable. Simply snap Clip-it to your charger and slide the Lightning connector in to the tray. The tray makes it possible to take out your phone including the Lightning connector to hold it in your hand for incoming messages and afterwards you can easily dock it again.
Clip-it Lightning US is specially designed for the new iPhone 5 and the included Apple USB Power Adapter (US version).
The European version of Clip-it Lightning is available here.
A multipack of 5 units with reduced prices is available here.
A multipack of 10 units with reduced prices is available here.
Clip-it is manufactured by innovative 3D-printing in tough but lightweight polyamide. The surface has a fine texture. The product will be shipped in basic Shapeways packaging. Some powder residue from the 3D-printing process may be found on the product itself; if this is the case, it should be easy to clean off with small tooth sticks & brushes. When you ordered Clip-it in colour it might be wise to clean it with water under the tap, so the dyeing pigments that might still be on the product don’t colour your white Apple gadgets. For further information & support contact the Shapeways customer service.
Your iPhone 5 charge buddy on the go.
Clip-it for iPhone converts your iPhone charger to a wall dock; making sure that you can easily charge your phone at every wall socket. Unfurnished rooms, hotels and conference rooms are no longer a problem.
Clip-it makes use of your new Apple Lightning Connector to USB Cable. Simply snap Clip-it to your charger and slide the Lightning connector in to the tray. The tray makes it possible to take out your phone including the Lightning connector to hold it in your hand for incoming messages and afterwards you can easily dock it again.
Clip-it Lightning US is specially designed for the new iPhone 5 and the included Apple USB Power Adapter (US version).
The European version of Clip-it Lightning is available here.
A multipack of 5 units with reduced prices is available here.
A multipack of 10 units with reduced prices is available here.
Clip-it is manufactured by innovative 3D-printing in tough but lightweight polyamide. The surface has a fine texture. The product will be shipped in basic Shapeways packaging. Some powder residue from the 3D-printing process may be found on the product itself; if this is the case, it should be easy to clean off with small tooth sticks & brushes. When you ordered Clip-it in colour it might be wise to clean it with water under the tap, so the dyeing pigments that might still be on the product don’t colour your white Apple gadgets. For further information & support contact the Shapeways customer service.
