by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
TheoJansen
The third public evolution of the Animaris Geneticus Parvus. #7 has evolved legs, with pointy feet instead of flat. Featuring a fully working Theo Jansen mechanism as used in his work "the Rhinoceros".
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
by
TheoJansen
[Note: This propeller propulsion add-on does not include a 3D printed Strandbeest, which should be bought seperately! This propeller does not fit the Ondula version!]
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
