Add some nature to your finger with this delicate ring of a branch.

With a cute little bird!

~

Personalize your ring by choosing a ring size.

Default size is 5 (USA) / 15 (NL)

If you want another size than listed below, please don't hesitate to ask me! ^_^

~

Sizes

~

Size 5 / 15

Inner diameter: 0.61 inch / 15.70 mm

Inner circumference: 1.94 inch / 49.21 mm

~

Size 6 / 16

Inner diameter: 0.64 inch / 16.51 mm

Inner circumference: 2.06 inch / 52.39 mm

~

Size 7 / 17

Inner diameter: 0.68 inch / 17.35 mm

Inner circumference: 2.19 inch / 55.56 mm

~

Size 8 / 18

Inner diameter: 0.71 inch / 18.19 mm

Inner circumference: 2.31 inch / 58.74 mm

~

Size 9 / 19

Inner diameter: 0.74 inch / 18.89 mm

Inner circumference: 2.44 inch / 61.91 mm

~

Size 10 / 20

Inner diameter: 0.77 inch / 19.84 mm

Inner circumference: 2.56 inch / 65.09 mm

~

Size 11 / 21

Inner diameter: 0.81 inch / 20.68 mm

Inner circumference: 2.69 inch / 68.26 mm

Interlocking bricks fashioned after Minecraft blocks. Each face has complementary studs and holes for both vertical and horizontal building. Intended for printing with Full Color Sandstone.

WIP. Still tweaking the textures, and still need to test the interlocking feature.

1) Grass and Dirt block - http://www.minecraftwiki.net/wiki/Grass
2) Dirt block - http://www.minecraftwiki.net/wiki/Dirt
3) Stone block - http://www.minecraftwiki.net/wiki/Stone
4) Wood block - http://www.minecraftwiki.net/wiki/Wood
5) Leaves block - www.minecraftwiki.net/wiki/Leaves
6) Brick block - www.minecraftwiki.net/wiki/Brick

www.minecraftwiki.net/wiki/Brick_%28Block%297) Wooden Plank block - www.minecraftwiki.net/wiki/Wooden_Plank
8) Pumpkin block - www.minecraftwiki.net/wiki/Pumpkin

Unfortunately Shapeways will not print this due to their pricing structure. Please let me know if you have any questions?

We have created an alternative 580mm high flat version  

A 150mm version can be ordered here 

There is also a 75mm version here  and a 300mm version here 

This is a truly inspiring piece, designed to use the minimum material and the largest print size while keeping the cost low. This is huge at 570mm high, it's a show stopper a head turner. Shapeways have been pushed to their limits to produce and ship this. It is fragile and care must be taken but once it is hanging from a wall with a small pin or nail. The fine 1mm wire structure comes together to create a wonderful huge majestic stag head and a wonderful balance of weight in the form while almost being invisible.

I created a post of the development and unboxing here 

The design is available as 2D print here Society 6 

This deer is from a short film called "the Hunt" https://vimeo.com/17691326

This version of the Pendant is very large, possibly too large to be printed in Steel.

The Minotaur Ring designed by Bits to Atoms and 3D Printed in the material of your choice, on demand by Shapeways.

Inspired Minotaur by The Drones http://www.youtube.com/watch?v=YX34Lxcj5J8&feature=player_embedded Standard size is US 11/34 66mm circ 21.24 diam

Personalized to your exact specifications on demand. Bits to Atoms is a range of unisex, bespoke 3D printed jewelry. Range includes rings, pendants, broaches and earrings.

A smaller version of a dragon I made

Detailed five-petal spiral flower bloom pendant with built-in loop for chain or chord. Chain or chord not included. Each stamen is attached to the bloom petals at both ends to minimize the possibility of breakage. At just over 4.6 cm diameter, this is a solid design that is available in a variety of materials to suit your taste and budget, ranging from paint-ready plastics to polished metals. From just $15 US. Artist rendition. Actual colors and materials may vary.

https://vimeo.com/17691326 This man is one of the stars of the short film "The Hunt"

Solamars Minecraft V34 3mm: An attempt to make a minecraft model representative of everything Minecraft in the smallest area. Lots of detail! Minecraft Diamond Emerald Mining House

Hunger Games inspired ring! District 12, the district of Katniss Everdeen and Peeta Mellark. Show support for your favorite district. Available in sizes 4-14.

Custom miniature I made according to my little bro's spec.
The face and the human ears where taken from free(I hope!) models.
Made in blender.

Zwergrüsseldickdick with pen

Also available in medium size with sew holes.

Get yourself or your dog ready for the Renaissance Festival with this medieval shield style pendant / pet tag. Choose from a Templar style cross for yourself, or a "Bone-shaped" cross for your dog. Features up to 3 lines of customizable text inset on both the front and back. Available in plain stainless steel, bronze finish, gold plated, or in solid Sterling Silver. You and/or your pet can wear this pendant with pride. This pendant is also suitable as a key fob. Want to customize this item beyond what is listed in the options? Feel free to contact me with any custom changes or suggestions.

See my other custom pet tag designs here.

Model of an origami crane. Not actually folded, but made to look like it was. Has a hole through the middle so you can get a bunch in different colors and string them together.