Helijenks
I design Scale accessories in 3D - (Inventor) for the RC Modelling community
Expertise:
- 3D modeler
- Product designer
- Artist
- Maker
by
Helijenks
Huey 1:6 Scale Seat Frame Deck Fixing Point - required for all seat legs, these are fitted to the bottom of the legs with an M2 washer and Self Tapper to allow the twist lock flange to operate, it is then locked in position with the "Ring Pin".
by
Helijenks
Helicopter Casing Clip (Working) with Lock pin - suitable for all scale Models, this item is currently 1:6 scale
by
Helijenks
1:6 Scale Huey Cyclic Stick - Can be made operational, comes with a base shroud capture plate for the cyclic "Boot" cover. Can be available in any scale, contact helijenks@gmail.com. File Revised 22/5/13 - (Reduced tolerances and increased wall thickness on base). If you require any pictures to assist in the assembly please contact helijenks@gmail.com
by
Helijenks
Revised (20/05/13) - Helicopter Yaw Control Pedals (Bell) 1:6 Scale
The Foot Pedals can be made to work (All parts movable) but you will require M1.6 & M2 Nuts and bolts to complete, they come complete with a bell-crank to link the two sets together. This file has just been updated to reduce tolerances that were allowed for in the original to allow printing as a complete assembly, however, they were too large hence the product change. Contact helijenks@gmail.com for different scales.
by
Helijenks
1:6 Scale Collective Stick for the Huey (Bell) - engraved lettering, requires assembly. There is access to fit a 2.5 mm LED at the Engine Idle position ... Simply the best ever !
by
Helijenks
1:6 Scale NAV Light Lens (Clear Material) - This needs to be ordered in conjunction with the NAV Light and ..... to the same scale that you have ordered the NAV Light.
by
Helijenks
1:6 scale Nav Light - The base has a slight camber on it to allow mounting onto a curved section of the fuselage, if not required - this can be sanded to a flat surface. NOTE: this part needs to have the Clear Glass Lens ordered with it.
There is a 3.2 mm Hole to fit standard LED
by
Helijenks
4mm Wide Pad Eye with 16mm Dia curve base that gives a fixing parallel to the skid.
by
Helijenks
4mm Dia Pad Eye that fits to skids with lateral hole to the skid.
by
Helijenks
1:6 Scale Seat Frame for Huey Rear Cabin, requires Seat Deck fixing points if full scale detail is required - to be ordered separately (Minimum 4 Required).File revised on 22/5/13 to increase wall thickness on frame spars. If you require any pictures to assist in the assembly please contact helijenks@gmail.com
by
Helijenks
1:6 Scale HUEY (Iroquois - UH-1 Series) Weapons System for the STARBOARD side, Including the fully detailed Weapons Support System, Rocket Launcher, Gatling Gun and Ammo Box for Door Gunner Weapon (M213).
Movable Parts where applicable in fantastic detail.
This is the STARBOARD side assembly only, please order with the Port Side Assembly.
The M213 (Door Gunner Weapon) will fit in the small arms mount and should be ordered separately.
Ammo Feed belts (in Rubberised material) need to be ordered separately.
Includes Mountings to the Fuselage.
For different Scale requirements - please state when ordering or contact Helijenks@gmail.com - since prices will vary.
by
Helijenks
1:6 Scale HUEY (Iroquois - UH-1 Series) Weapons System for the PORT side, Including the fully detailed Weapons Support System, Rocket Launcher, Gatling Gun and Ammo Box for Door Gunner Weapon (M213).
Movable Parts where applicable in fantastic detail.
This is the PORT side assembly only, please order with the Starboard Side Assembly.
The M213 (Door Gunner Weapon) will fit in the small arms mount and should be ordered separately.
Ammo Feed belts (in Rubberised material) need to be ordered separately.
Includes Mountings to the Fuselage.
For different Scale requirements - please state when ordering or contact Helijenks - since prices will vary.
by
Helijenks
16mm Radius x 260mm Skid Protector for Bell Helicopters, I can supply in different Radius and length, 4 off are required for the LM Huey, they butt together at a clamping band so the joint is partially hidden.
Contact helijenks@gmail.com for modified items
by
Helijenks
3mm wide (internally) Mounting Bracket and fixing point for use with Cable Cutters or other items to be fixed to fuselages.
by
Helijenks
Helicopter Pilot Seat 1:6 Scale - This model is adjustable for the seat angle, height and position. A superb addition to most helicopter cockpit's ... especially Huey's!
by
Helijenks
Huey 1:6 Scale Rear Cabin Seat Frame Assembly to suit LM Huey, can be scaled down to fit other models - Contact Helijenks@gmail.com.
All parts are movable and the model is supplied with Safety Harness Clips (8).
This model requires the "Seat Frame Deck Fixing" points for correct Scale detail and ... the ability to install and remove reasonably easily (4 Minimum Required)
by
Helijenks
Various parts required to complete the build of 1:6 Scale Huey Center Console, include embossed Dials and Barrels showing Frequecies, Ammo Count and Gun Angle. For different scales Contact helijenks@gmail.com
by
Helijenks
32 mm Arc Cantilever Hinge with Clevis type fixing, to suit 2mm Nut & Bolt
by
Helijenks
"Tail End" Skid Cap to finish of the Scale detail - available in different diameters. Contact helijenks@gmail.com for special orders
by
Helijenks
16mm Dia Skid Protectors 320mm Long each (2 off required per side)
by
Helijenks
The box has an operational hinged Lid, you will need to create the hinge pin with 1.5mm wire - Suits all 1:6 Scale Helicopters. 2 x Thermos Flasks included.
Contact helijenks@gmail.com for different scale models
by
Helijenks
Wire Cutter Blade(s) - Stay Assembly Kit for 1:4 to 1:6 Scale Kits. If other sizes are required ...contact helijenks@gmail.com
by
Helijenks
Overhead Panel to suit LM Huey 1:6:5 Scale, can be scaled down to suit. It has embossed lettering where shown. For variants in Scale contact helijenks@gmail.com
by
Helijenks
HUEY UH- 1B Center Console at 1:6:5 scale to suit LM Huey (and others)
Requires the Center Cole Assembly parts to complete (Sold separetly)
The most incredible detail with embossed lettering on the panels and levers - simply the best !
For different scales Contact helijenks@gmail.com
by
Helijenks
1:7 scale Top of Fuselage Cable Cutter with support arms & mounts, can be made in other scales - Contact : helijenks@gmail.com
by
Helijenks
1:7 Scale Cable Cutters to Suit Bell Helicopter, This set can be used either on the top or bottom of the fuselage, however, they are really for under the fuselage - can be made in different scales, contact: helijenks@gmail.com
by
Helijenks
1:6 Scale Helicopter Pilot Seat Frame & seat, requires Base unit to be ordered separately. When assembled, this seat will elevate, slide & Tilt. The "Rolls Royce" of Pilot Seats. Contact helijenks@gmail.com for more info
by
Helijenks
Huey - Single Rear Cabin Seat 1:6 scale , (requires assembly) and Deck Fixing Points (4 Off) to be ordered separately. This superb Framework will now need a bit Sewing done on it to complete!
by
Helijenks
Fitting required for the full assembly of the Port & Starboard Side Huey Weapons Systems - This is one set only and has spares included, 2 sets are required if Port & Starboard Wepons systems are to be ordered.
