by
TheoJansen
The third public evolution of the Animaris Geneticus Parvus. #7 has evolved legs, with pointy feet instead of flat. Featuring a fully working Theo Jansen mechanism as used in his work "the Rhinoceros".
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
by
TheoJansen
[Note: This propeller propulsion add-on does not include a 3D printed Strandbeest, which should be bought seperately! This propeller does not fit the Ondula version!]
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
by
curvecreative
Bugle for iPhone 5
AVAILABLE NOW!
Enjoy your music louder with the Bugle
The Bugle is a natural acoustic amplifier for your iPhone that fits snuggly over the speaker, acts as a stand and makes your music sound better and louder. The Bugle is curved to provide a natural flex that assures a snug fit on your iPhone.
A great solution for bringing anywhere and requires no batteries. Just chuck it in your bag and use it for music at the park, for watching a film, or for sharing a youtube video
Available for iPhone 4 / 4S here
