Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.

This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!

NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small

Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !

Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.

Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.

Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later. +

The best triply periodic minimal surface ever!

I put a bigger one here.

The filigree design over the skull symbolizes ever growing renewal over the ghost of the past. This is the original design as featured on Kickstarter. It became their #1 most funded sculpture project of all time. Small is pictured sitting in the hand. See pic of all 3 sizes together for comparison.

The Hyphae lamp is a series of organic table lamps based on how veins form in leaves. Each lamp is a completely one-of-a-kind design 3D-printed in nylon plastic. The lamps are lit by eco-friendly LED's and cast dramatic branching shadows on the wall and ceiling. 

Video
watch it grow at http://vimeo.com/nervoussystem/hyphaelamp

About Hyphae
Hyphae is a collection of 3D printed artifacts constructed of rhizome-like networks. Inspired by the vein structures that carry fluids through organisms from the leaves of plants to our own circulatory systems, we created a simulation which uses physical growth principles to build sculptural, organic structures. Starting from an initial seed and a surface, we grow a hierarchical network where nodes constantly branch and merge. The densely interconnected structure is at once airy and strong.

Lighting Specifications
The lamp comes with an eco-friendly 3-watt 200 lumen LED light fixture with three bright Cree LED's that will last for 6 years of continuous use. It is UL-listed and works off a 120V or 240V outlet.

Please contact us at http://n-e-r-v-o-u-s.com/contact.php to receive the lighting components for the lamp.  We will send them to you free of charge if you purchase the lamp shade.

I created the skeleton of a skeletal Lepidoptera. The Death's Head Hawkmoth (Acherontia atropos), seen on The Silence of the Lambs , has a skull marking on its back. I made a full human-like bone structure for the moth, with the grinning skull protruding from its back.

The model is very thin, yet sturdy and flexible. Detail level is fantastic, and the natural texture of the 3d printing process gives it a bone-like appearance that works wonders.

Yes, moths don't have endoskeletons, that's the whole point...

A delightful surface: the gyroid put through a simple inverse transformation. It's ellipsoidal on the outside, and there is a sphere taken out of the center, which is difficult to see; for otherwise it would be infinitely tiny inside, and therefore unprintable.

This piece of art was created in 3D software by "printedCat" 3D-designer in San Francisco, California, USA and printed in nylon material by Shapeways.com in Holland or New York.

Enjoy watching!

All images are photos of real objects. "Proof Printed".

printedCat on Shapeways
printedCat.com
printedCat on Flickr
printedCat on YouTube
printedCat on Etsy
printedCat on Facebook

• A design based on the "DNA Double Helix"

Related Designs:
"DNA" Flower Wall Ornament
"Drink to Your DNA!" - Espresso & Sake Tower Cup
DNA ENDLESS COLUMN 2012 - HOMAGE TO BRANCUSI

This implicit surface was generated and a shell was added to the isosurface in MeshLab.

Please check out all of the other implicit surfaces in my shop. implicit surfaces at vertigo polka